13/30264591 DC : 0
NA
Status of Standard is Unknown
BS EN 60747-14-6 ED 1.0 - SEMICONDUCTOR DEVICES - PART 14-6: SEMICONDUCTOR SENSORS - HUMIDITY SENSOR
Hardcopy , PDF
English
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 The signs
5 Essential elements and feature
6 Measurement methods
7 Test methods of the reliability
BS EN 60747-14-6 ED 1.0.
Committee |
EPL/47
|
DocumentType |
Draft
|
Pages |
34
|
PublisherName |
British Standards Institution
|
Status |
NA
|
IEC 60749-20:2008 | Semiconductor devices - Mechanical and climatic test methods - Part 20: Resistance of plastic encapsulated SMDs to the combined effect of moisture and soldering heat |
IEC 60749-17:2003 | Semiconductor devices - Mechanical and climatic test methods - Part 17: Neutron irradiation |
IEC 60749-8:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 8: Sealing |
IEC 60749-21:2011 | Semiconductor devices - Mechanical and climatic test methods - Part 21: Solderability |
IEC 60749-25:2003 | Semiconductor devices - Mechanical and climatic test methods - Part 25: Temperature cycling |
IEC 60749-30:2005+AMD1:2011 CSV | Semiconductor devices - Mechanical and climatic test methods - Part 30: Preconditioning of non-hermetic surface mount devices prior to reliability testing |
IEC 60749-5:2017 | Semiconductor devices - Mechanical and climatic test methods - Part 5: Steady-state temperature humidity bias life test |
IEC 60749-4:2017 | Semiconductor devices - Mechanical and climatic test methods - Part 4: Damp heat, steady state, highly accelerated stress test (HAST) |
IEC 60749-31:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 31: Flammability of plastic-encapsulated devices (internally induced) |
IEC 60749-1:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 1: General |
IEC 60749-29:2011 | Semiconductor devices - Mechanical and climatic test methods - Part 29: Latch-up test |
IEC 60749-11:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 11: Rapid change of temperature - Two-fluid-bath method |
IEC 60749-36:2003 | Semiconductor devices - Mechanical and climatic test methods - Part 36: Acceleration, steady state |
IEC 60749-18:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 18: Ionizing radiation (total dose) |
IEC 60749-27:2006+AMD1:2012 CSV | Semiconductor devices - Mechanical and climatic test methods - Part27: Electrostatic discharge (ESD) sensitivity testing - Machine model (MM) |
IEC 60749-16:2003 | Semiconductor devices - Mechanical and climatic test methods - Part 16: Particle impact noise detection (PIND) |
IEC 60749-9:2017 | Semiconductor devices - Mechanical and climatic test methods - Part 9: Permanence of marking |
IEC 60749-33:2004 | Semiconductor devices - Mechanical and climatic test methods - Part 33: Accelerated moisture resistance - Unbiased autoclave |
IEC 60749-24:2004 | Semiconductor devices - Mechanical and climatic test methods - Part 24: Accelerated moisture resistance - Unbiased HAST |
IEC 60721-2-1:2013 | Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity |
IEC 60747-14-1:2010 | Semiconductor devices - Part 14-1: Semiconductor sensors - Generic specification for sensors |
IEC 60749-15:2010 | Semiconductor devices - Mechanical and climatic test methods - Part 15: Resistance to soldering temperature for through-hole mounted devices |
IEC 60749-26:2013 | Semiconductor devices - Mechanical and climatic test methods - Part 26: Electrostatic discharge (ESD) sensitivity testing - Human body model (HBM) |
IEC 60721-3-0:1984+AMD1:1987 CSV | Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Introduction |
IEC 60749-35:2006 | Semiconductor devices - Mechanical and climatic test methods - Part 35: Acoustic microscopy for plastic encapsulated electronic components |
IEC 60749-7:2011 | Semiconductor devices - Mechanical and climatic test methods - Part 7: Internal moisture content measurement and the analysis of other residual gases |
IEC 60747-1:2006+AMD1:2010 CSV | Semiconductor devices - Part 1: General |
IEC 60749-13:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 13: Salt atmosphere |
IEC 60749-34:2010 | Semiconductor devices - Mechanical and climatic test methods - Part 34: Power cycling |
IEC 60749-6:2017 | Semiconductor devices - Mechanical and climatic test methods - Part 6: Storage at high temperature |
IEC 60749-2:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 2: Low air pressure |
ISO/IEC Guide 2:2004 | Standardization and related activities General vocabulary |
IEC 60749-3:2017 | Semiconductor devices - Mechanical and climatic test methods - Part 3: External visual examination |
IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
IEC 60749-10:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 10: Mechanical shock |
IEC 60749-32:2002+AMD1:2010 CSV | Semiconductor devices - Mechanical and climatic test methods - Part 32: Flammability of plastic-encapsulated devices (externally induced) |
IEC 60749-14:2003 | Semiconductor devices - Mechanical and climatic test methods - Part 14: Robustness of terminations (lead integrity) |
IEC 60749-19:2003+AMD1:2010 CSV | Semiconductor devices - Mechanical and climatic test methods - Part 19: Die shear strength |
IEC 60749-22:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 22: Bond strength |
IEC 60749-12:2002 | Semiconductor devices - Mechanical and climatic test methods - Part 12: Vibration, variable frequency |
IEC 60721-3-1:1997 | Classification of environmental conditions - Part 3 Classification of groups of environmental parameters and their severities - Section 1: Storage |
IEC 60749-23:2004+AMD1:2011 CSV | Semiconductor devices - Mechanical and climatic test methods - Part 23: High temperature operating life |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.