BS EN 61076-3-119 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-119: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR UNSHIELDED, FREE AND FIXED 10 WAY CONNECTORS WITH PUSH-PULL COUPLING FOR INDUSTRIAL ENVIRONMENTS WITH FREQUENCIES UP TO 100 MHZ

Available format(s)

Hardcopy , PDF

Language(s)

English

Publisher

British Standards Institution

FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Technical information
5 Dimensional information
6 Characteristics
7 Test schedule

BS EN 61076-3-119.

Committee	EPL/48
DocumentType	Draft
Pages	33
PublisherName	British Standards Institution
Status	NA

IEC GUIDE 109:2012	Environmental aspects - Inclusion in electrotechnical product standards
IEC 61076-1:2006	Connectors for electronic equipment - Product requirements - Part 1: Generic specification
IEC 60512-11-4:2002	Connectors for electronic equipment - Tests and measurements - Part 11-4: Climatic tests - Test 11d: Rapid change of temperature
IEC 60512-11-9:2002	Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat
IEC 60512-11-10:2002	Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold
IEC 61984:2008	Connectors - Safety requirements and tests
IEC 60512-3-1:2002	Connectors for electronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance
IEC 60068-1:2013	Environmental testing - Part 1: General and guidance
IEC 60068-2-20:2008	Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
IEC 60512-13-5:2006	Connectors for electronic equipment - Tests and measurements - Part 13-5: Mechanical operation tests - Test 13e: Polarizing and keying method
IEC 60512-6-3:2002	Connectors for electronic equipment - Tests and measurements - Part 6-3: Dynamic stress tests - Test 6c: Shock
IEC 60512-15-1:2008	Connectors for electronic equipment - Tests and measurements - Part 15-1: Connector tests (mechanical) - Test 15a: Contact retention in insert
ISO 1101:2017	Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 11469:2016	Plastics — Generic identification and marking of plastics products
IEC 60512-13-2:2006	Connectors for electronic equipment - Tests and measurements - Part 13-2: Mechanical operation tests - Test 13b: Insertion and withdrawal forces
IEC 60512-16-5:2008	Connectors for electronic equipment - Tests and measurements - Part 16-5: Mechanical tests on contacts and terminations - Test 16e: Gauge retention force (resilient contacts)
ISO 1302:2002	Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
IEC 60512-26-100:2008+AMD1:2011 CSV	Connectors for electronic equipment - Tests and measurements - Part 26-100: Measurement setup, test and reference arrangements and measurements for connectors according to IEC 60603-7 - Tests 26a to 26g
IEC 60512-11-3:2002	Connectors for electronic equipment - Tests and measurements - Part 11-3: Climatic tests - Test 11c: Damp heat, steady state
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	Degrees of protection provided by enclosures (IP Code)
IEC 60603-7:2008+AMD1:2011 CSV	Connectors for electronic equipment - Part 7: Detail specification for 8-way, unshielded, free and fixed connectors
IEC 60512-1-1:2002	Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination
IEC 60512-11-1:1995	Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 11: Climatic tests - Section 1: Test 11a - Climatic sequence
IEC 60512-2-1:2002	Connectors for electronic equipment - Tests and measurements - Part 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method
IEC 60512-9-1:2010	Connectors for electronic equipment - Tests and measurements - Part 9-1: Endurance tests - Test 9a: Mechanical operation
IEC 60512-11-7:2003	Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
ISO 128-1:2003	Technical drawings General principles of presentation Part 1: Introduction and index
IEC 60512-5-2:2002	Connectors for electronic equipment - Tests and measurements - Part 5-2: Current-carrying capacity tests - Test 5b: Current-temperature derating
IEC 60512-11-12:2002	Connectors for electronic equipment - Tests and measurements - Part 11-12: Climatic tests - Test 11m: Damp heat, cyclic
IEC 60512-4-1:2003	Connectors for electronic equipment - Tests and measurements - Part 4-1: Voltage stress tests - Test 4a: Voltage proof
IEC 62197-1:2006	Connectors for electronic equipment - Quality assessment requirements - Part 1: Generic specification
IEC 60512-15-7:2008	Connectors for electronic equipment - Tests and measurements - Part 15-7: Connector tests (mechanical) - Test 15g: Robustness of protective cover attachment
IEC 60512-6-4:2002	Connectors for electronic equipment - Tests and measurements - Part 6-4: Dynamic stress tests - Test 6d: Vibration (sinusoidal)
IEC 60512-15-6:2008	Connectors for electronic equipment - Tests and measurements - Part 15-6: Connector tests (mechanical) - Test 15f: Effectiveness of connector coupling devices
IEC 60050-581:2008	International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
IEC 60512-1-2:2002	Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
IEC GUIDE 114:2005	Environmentally conscious design - Integrating environmental aspects into design and development of electrotechnical products