• 17/30345075 DC : 0

    NA Status of Standard is Unknown
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    BS EN ISO 11296-4 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Pipes at the 'M' stage
    6 Fittings at the 'M' stage
    7 Ancillary components
    8 Fitness for purpose of the installed lining system
      at the 'I' stage
    9 Installation practice
    Annex A (informative) - CIPP components and their functions
    Annex B (normative) - Cured-in-place pipes - Determination
            of short-term flexural properties
    Annex C (normative) - Cured-in-place pipes - Determination
            of long-term flexural modulus under dry or wet
            conditions
    Annex D (normative) - Cured-in-place pipes - Determination
            of long-term flexural strength under dry, wet or acidic
            conditions (stress corrosion test)
    Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PRI/88/3
    Document Type Draft
    Publisher British Standards Institution
    Status NA

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 8773:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP)
    ISO 7685:1998 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
    ISO 10928:2016 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Methods for regression analysis and their use
    ISO 75-2:2013 Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 13002:1998 Carbon fibre Designation system for filament yarns
    ISO 8513:2016 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the initial longitudinal tensile strength
    ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
    ISO 899-2:2003 Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
    ISO 14125:1998 Fibre-reinforced plastic composites Determination of flexural properties
    ISO 7684:1997 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the creep factor under dry conditions
    ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
    ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
    ISO 178:2010 Plastics Determination of flexural properties
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective