BS EN 63075 - SUPERCONDUCTING AC POWER CABLES AND THEIR ACCESSORIES FOR RATED VOLTAGES FROM 6 KV TO 500 KV - TEST METHODS AND REQUIREMENTS

Available format(s)

Hardcopy , PDF

Language(s)

English

Publisher

British Standards Institution

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Voltage and current designations
5 Cable materials
6 Cable characteristics
7 Accessory characteristics
8 Test conditions
9 Routine tests on cables and on prefabricated
accessories
10 Sample tests on cables
11 Sample tests on accessories
12 Type tests on cable systems
13 Prequalification test of the cable system
14 Type test on cables
15 Type test on accessories
16 Tests after installation
Annex A (informative) - Cooling system considerations
Annex B (informative) - Critical current (I[c]) measurement
Annex C (informative) - Tests for engineering information
Annex D (informative) - List of type tests of cable systems
Annex E (normative) - Tests of outer protection for joints
Bibliography

BS EN 63075.

Committee	GEL/20/17
DocumentType	Draft
Pages	52
PublisherName	British Standards Institution
Status	NA

IEC 60811-501:2012	Electric and optical fibre cables - Test methods for non-metallic materials - Part 501: Mechanical tests - Tests for determining the mechanical properties of insulating and sheathing compounds
IEC 60811-509:2012+AMD1:2017 CSV	Electric and optical fibre cables - Test methods for non-metallic materials - Part 509: Mechanical tests - Test for resistance of insulations and sheaths to cracking (heat shock test)
IEC 60811-506:2012	Electric and optical fibre cables - Test methods for non-metallic materials - Part 506: Mechanical tests - Impact test at low temperature for insulations and sheaths
IEC 60811-505:2012	Electric and optical fibre cables - Test methods for non-metallic materials - Part 505: Mechanical tests - Elongation at low temperature for insulations and sheaths
IEC 60811-504:2012	Electric and optical fibre cables - Test methods for non-metallic materials - Part 504: Mechanical tests - Bending tests at low temperature for insulation and sheaths
IEC 60885-3:2015 RLV	Electrical test methods for electric cables - Part 3: Test methods for partial discharge measurements on lengths of extruded power cables
IEC 60811-203:2012	Electric and optical fibre cables - Test methods for non-metallic materials - Part 203: General tests - Measurement of overall dimensions
IEC 60811-401:2012+AMD1:2017 CSV	Electric and optical fibre cables - Test methods for non-metallic materials - Part 401: Miscellaneous tests - Thermal ageing methods - Ageing in an air oven
IEC 60811-409:2012	Electric and optical fibre cables - Test methods for non-metallic materials - Part 409: Miscellaneous tests - Loss of mass test for thermoplastic insulations and sheaths
IEC 60811-202:2012+AMD1:2017 CSV	Electric and optical fibre cables - Test methods for non-metallic materials - Part 202: General tests - Measurement of thickness of non-metallic sheath
IEC 60332-1-2:2004+AMD1:2015 CSV	Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame
IEC 60230:1966	Impulse tests on cables and their accessories
IEC TS 62478:2016	High voltage test techniques - Measurement of partial discharges by electromagnetic and acoustic methods
IEC 60183:2015	Guidance for the selection of high-voltage A.C. cable systems
IEC 60811-508:2012+AMD1:2017 CSV	Electric and optical fibre cables - Test methods for non-metallic materials - Part 508: Mechanical tests - Pressure test at high temperature for insulation and sheaths
IEC 60229:2007	Electric cables - Tests on extruded oversheaths with a special protective function
IEC 60059:1999+AMD1:2009 CSV	IEC standard current ratings
IEC 60060-1:2010	High-voltage test techniques - Part 1: General definitions and test requirements
IEC 60811-605:2012	Electric and optical fibre cables - Test methods for non-metallic materials - Part 605: Physical tests - Measurement of carbon black and/or mineral filler in polyethylene compounds