AGMA 2001 : D
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy
04-10-2016
English
01-01-2004
Foreword
1 Scope
2 Normative references, definitions and symbols
3 Application
4 Criteria for tooth capacity
5 Fundamental rating formulas
6 Geometry factors, I and J
7 Transmitted tangential load, W[t]
8 Dynamic factor, K[v]
9 Overload factor, K[o]
10 Service factor
11 Safety factors, S[H] and S[F]
12 Elastic coefficient, C[p]
13 Surface condition factor, C[f]
14 Hardness ratio factor, C[H]
15 Load distribution factor, K[m]
16 Allowable stress numbers, s[ac] and s[at]
17 Stress cycle factors, Z[N] and Y[N]
18 Reliability factor, K[R]
19 Temperature factor, K[T]
20 Size factor, K[s]
Bibliography
Annexes
A Method for determination of dynamic factor with AGMA 2000-A88
B Rim thickness factor, K[B]
C Application analysis
D Discussion of the analytical face or longitudinal load
distribution factor
E Gear material fatigue life
F Controlling section size considerations for through hardened
gearing
Figures
Tables
Describes a comprehensive method for rating the pitting resistance and bending strength of spur and helical involute gear pairs. Includes detailed discussions of factors influencing gear survival and calculation methods.
| DevelopmentNote |
Supersedes AGMA 218.01 (03/2002) Supplement is available separately, see record AGMA 925. (02/2015) Metric Edition of this standard is available as AGMA 2101. (04/2016)
|
| DocumentType |
Standard
|
| Pages |
66
|
| PublisherName |
American Gear Manufacturers Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| MIL-L-80277 Base Document:1989 | LATHES, PRECISION, TOOLROOM, VARIABLE SPEED, 11-INCH THROUGH 13-INCH |
| 03/314804 DC : DRAFT SEP 2003 | BS ISO 6336-3 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 3: CALCULATION OF TOOTH BENDING STRENGTH |
| BS ISO 6336-3:2006 | Calculation of load capacity of spur and helical gears Calculation of tooth bending strength |
| MIL-L-23251 Revision E:1989 | LATHES, ENGINE AND TOOLROOM 2516 AND 3220 |
| CSA B354.5 : 2007 : R2016 | MAST-CLIMBING WORK PLATFORMS |
| AGMA 6023 : REV A : 1988 : R2000 | DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES |
| MIL-S-80271 Revision A:1992 | SHEARING MACHINE, METAL SQUARING MECHANICAL DRIVE |
| AGMA 1012 : 2005 | GEAR NOMENCLATURE, DEFINITIONS OF TERMS WITH SYMBOLS |
| B354.12-17 | Design, calculations, safety requirements, and test methods for mast climbing transport platforms (MCTPs) |
| AGMA 6013:2016(R2021) | INDUSTRIAL ENCLOSED GEAR DRIVES |
| A-A-59469 Base Document:1999 | Washer-Extractor, Laundry, 35 to 200 Pound Capacity (Naval Shipboard) |
| ASME BTH 1 : 2017 | DESIGN OF BELOW-THE-HOOK LIFTING DEVICES |
| AGMA 938 : A | SHOT PEENING OF GEARS |
| 03/314803 DC : DRAFT SEP 2003 | ISO 6336-2 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 2: CALCULATION OF SURFACE DURABILITY (PITTING) |
| API SPEC 11E : 2013 | SPECIFICATION FOR PUMPING UNITS |
| AGMA 912 : A | MECHANISMS OF GEAR TOOTH FAILURE |
| AGMA 6010 : REV F : 1997 : R2003 | STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES |
| AGMA 6001 : REV D : 1997 | DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES |
| API 2C RUSSIAN : 2004 | SPECIFICATION FOR OFFSHORE PEDESTAL MOUNTED CRANES |
| ISO/TS 10303-5001:2010 | Industrial automation systems and integration — Product data representation and exchange — Part 5001: Guidance on the usage of ISO 10303-214 for gear units |
| ISO 6336-1:2006 | Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors |
| B354.9-17 | Design, calculations, safety requirements, and test methods for mast climbing work platforms (MCWPs) |
| API 11E RUSSIAN : 2013 | SPECIFICATION FOR PUMPING UNITS |
| MIL-M-80255 Revision B:1990 | MACHINING CENTERS, VERTICAL, SINGLE SPINDLE, COMPUTER NUMERICAL CONTROL (CNC) |
| AGMA 6023 : A | DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES |
| AGMA 6023 : REV A : 1988 : R1993 | DESIGN MANUAL FOR ENCLOSED EPICYCLIC GEAR DRIVES |
| AGMA 6010 : REV F : 1997 | STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES |
| ISO 6336-3:2006 | Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength |
| API 613:2003 | SPECIAL PURPOSE GEAR UNITS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES |
| API SPEC 11E CHINESE : 2013 | SPECIFICATION FOR PUMPING UNITS |
| ISO 6336-2:2006 | Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) |
| 06/30157507 DC : 0 | BS ISO 10431 - PETROLEUM AND NATURAL GAS INDUSTRIES - PUMPING UNITS - SPECIFICATION |
| BS ISO 6336-2:2006 | Calculation of load capacity of spur and helical gears Calculation of surface durability (pitting) |
| AGMA 923 : B | METALLURGICAL SPECIFICATIONS OF STEEL GEARING |
| SAE J 1619 : 2017 | SINGLE TOOTH GEAR BENDING FATIGUE TEST |
| CSA B354.5 : 2007 : INC : UPD 1 : 2008 : R2011 | MAST-CLIMBING WORK PLATFORMS |
| BS ISO 6336-1:2006 | Calculation of load capacity of spur and helical gears Basic principles, introduction and general influence factors |
| CSA B354.5:2007 | MAST-CLIMBING WORK PLATFORMS |
| AGMA 6001 : REV D : 1997 : R2003 | DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES |
| AGMA 6010 : F | STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES |
| AGMA 937 : A2012(R2017) | AEROSPACE BEVEL GEARS |
| 04/30126837 DC : DRAFT DEC 2004 | BS ISO 6336-1 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 1: BASIC PRINCIPLES, INTRODUCTION AND GENERAL INFLUENCE FACTORS |
| MIL-L-80007 Revision E:1989 | LATHES, TOOLROOM, 11-INCH THROUGH 13-INCH |
| AGMA 6001 : D | DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES |
| API 2C : 2012 | OFFSHORE PEDESTAL-MOUNTED CRANES |
| ASME NUM 1 : 2009 | RULES FOR CONSTRUCTION OF CRANES, MONORAILS, AND HOISTS (WITH BRIDGE OR TROLLEY OR HOIST OF THE UNDERHUNG TYPE) |
| AGMA 933 : B | BASIC GEAR GEOMETRY |
| AGMA 2015-1 : A | ACCURACY CLASSIFICATION SYSTEM - TANGENTIAL MEASUREMENTS FOR CYLINDRICAL GEARS |
| AGMA 6011 : I | SPECIFICATION FOR HIGH SPEED HELICAL GEAR UNITS |
| AGMA 246.02 : A | RECOMMENDED PROCEDURE FOR CARBURIZED AEROSPACE GEARING |
| ISO/TR 10495:1997 | Cylindrical gears Calculation of service life under variable loads Conditions for cylindrical gears according to ISO 6336 |
| ASTM A 291 : 2003 | Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears and Shafts for Reduction Gears |
| AGMA 427.01 : 0 | INFORMATION SHEET - SYSTEMS CONSIDERATIONS FOR CRITICAL SERVICE GEAR DRIVES |
| AGMA 2000 : A | GEAR CLASSIFICATION AND INSPECTION HANDBOOK - TOLERANCES AND MEASURING METHODS FOR UNASSEMBLED SPUR AND HELICAL GEARS (INCLUDING METRIC EQUIVALENTS) |
| AGMA 1010 : E | APPEARANCE OF GEAR TEETH - TERMINOLOGY OF WEAR AND FAILURE |
| AGMA 2007 : C | GEARS - SURFACE TEMPER ETCH INSPECTION AFTER GRINDING |
| SAE AMS 2301 : 2015 | STEEL CLEANLINESS, AIRCRAFT QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE |
| AGMA 925 : A | EFFECT OF LUBRICATION ON GEAR SURFACE DISTRESS |
| AGMA 908 : B | GEOMETRY FACTORS FOR DETERMINING THE PITTING RESISTANCE AND BENDING STRENGTH OF SPUR, HELICAL AND HERRINGBONE GEAR TEETH |
| AGMA 9005 : E | INDUSTRIAL GEAR LUBRICATION |
| ASTM A 535 : 1985 | Specification for Special-Quality Ball and Roller Bearing Steel (Withdrawn 1998) |
| SAE AMS 2300 L : 2015 | STEEL CLEANLINESS, PREMIUM AIRCRAFT-QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE |
| AGMA 927 : A | LOAD DISTRIBUTION FACTORS - ANALYTICAL METHODS FOR CYLINDRICAL GEARS |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| AGMA 6033 : B | MATERIALS FOR MARINE PROPULSION GEARING |
| AGMA 2004 : C | GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL |
| AGMA 1012 : 2005 | GEAR NOMENCLATURE, DEFINITIONS OF TERMS WITH SYMBOLS |
| ASTM A 534 : 2017 : REDLINE | Standard Specification for Carburizing Steels for Anti-Friction Bearings |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.