AS 2439.2-1983

1 - AS 2439 Part 2-1983 PERFORATED PLASTICS DRAINAGE AND EFFLUENT PIPE AND FITTINGS - PERFORATED EFFLUENT PIPE AND ASSOCIATED FIT
4 - PREFACE
5 - CONTENTS
6 - 1 SCOPE.
6 - 2 REFERENCED DOCUMENTS.
6 - 3 TYPES AND CLASSIFICATION.
6 - 3.1 Types.
6 - 3.2 Classification.
6 - 4 MATERIAL.
6 - 5 FREEDOM FROM DEFECTS.
6 - 6 DIMENSIONS.
6 - 6.1 Diameter.
7 - 6.2 Length.
7 - 6.3 Wall Thickness.
7 - 7 PERFORATIONS.
7 - 7.1 Type 3 Pipe.
7 - 7.2 Type 4 Pipe.
7 - 8 FITTINGS.
7 - 9 PACKAGING.
7 - 10 CONDITIONING OF TEST SPECIMENS.
7 - 11 PERFORMANCE REQUIREMENTS.
7 - 11.1 Bending (Applicable to Type 3 only).
7 - 11.2 Straightening (Applicable to Type 3 only).
7 - 11.3 High Temperature Impact Resistance.
7 - 11.4 Low Temperature Impact Resistance.
7 - 11.5 Elongation (Applicable to Type 3 only).
7 - 11.6 Pipe Stiffness.
8 - 11.7 Perforation Deformation.
8 - 11.8 Joint Separation (Applicable to Type 3 only).
8 - 12 MARKING.
8 - 12.1 Type 3.
8 - 12.2 Type 4.
9 - APPENDIX A - DETERMINATION OF COMPLIANCE OF A LOT
9 - INTRODUCTION.
9 - A1 AUSTRALIAN STANDARDS MARK.
9 - A2 ASSESSMENT OF COMPLIANCE ON THE BASIS OF STATISTICAL SAMPLING
9 - A3 ASSURANCE OF COMPLIANCE ON THE BASIS OF SUPPLIERS’ QUALITY CONTROL SYSTEMS
10 - APPENDIX B - METHODS FOR MEASUREMENT OF DIMENSIONS
10 - B1 SCOPE.
10 - B2 APPARATUS.
10 - B3 PREPARATION OF TEST SPECIMENS
10 - B3.1 Diameter-Outside and Inside.
10 - B3.2 Length.
10 - B3.3 Perforations.
10 - B4 TEST PROCEDURE.
11 - B5 REPORT.
11 - B5.1 Outside Diameter.
11 - B5.2 Inside Diameter.
11 - B5.3 Length.
11 - B5.4 Perforations.
12 - APPENDIX C - BENDING TEST (TYPE 3 ONLY)
12 - C1 SCOPE.
12 - C2 PRINCIPLE.
12 - C3 APPARATUS.
12 - C4 PREPARATION OF TEST SPECIMENS.
12 - C5 TEST PROCEDURE.
12 - C6 REPORT.
13 - APPENDIX D - STRAIGHTENING TEST AT 0° C (TYPE 3 ONLY)
13 - D1 SCOPE.
13 - D2 PRINCIPLE.
13 - D3 APPARATUS.
13 - D4 PREPARATION OF TEST SPECIMENS.
13 - D5 TEST PROCEDURE.
13 - D6 REPORT.
14 - APPENDIX E - METHOD OF TEST FOR HIGH TEMPERATURE IMPACT RESISTANCE
14 - E1 SCOPE.
14 - E2 PRINCIPLE.
14 - E3 APPARATUS.
14 - E4 PREPARATION OF TEST SPECIMENS.
14 - E5 TEST PROCEDURE.
14 - E6 REPORT.
15 - APPENDIX F - METHOD OF TEST FOR LOW TEMPERATURE IMPACT RESISTANCE
15 - F1 SCOPE.
15 - F2 PRINCIPLE.
15 - F3 APPARATUS.
15 - F4 PREPARATION OF TEST SPECIMENS.
15 - F5 TEST PROCEDURE.
15 - F6 REPORT.
16 - APPENDIX G - METHOD FOR DETERMINING ELONGATION AND PERFORATION DEFORMATION (TYPE 3 ONLY)
16 - G1 SCOPE.
16 - G2 PRINCIPLE.
16 - G3 APPARATUS.
16 - G4 PREPARATION OF TEST SPECIMENS.
16 - G5 TEST PROCEDURE.
16 - G6 CALCULATION.
16 - G7 REPORT.
16 - G7.1 Pipe Elongation.
16 - G7.2 Perforation Deformation.
17 - APPENDIX H - METHOD FOR DETERMINING PIPE STIFFNESS AND PERFORATION DEFORMATION
17 - H1 SCOPE.
17 - H2 PRINCIPLE.
17 - H3 APPARATUS.
17 - H4 PREPARATION OF TEST SPECIMENS.
17 - H5 TEST PROCEDURE.
18 - H6 CALCULATIONS.
18 - H7 REPORT.
18 - H7.1 Pipe Stiffness.
18 - H7.2 Perforation Deformation (Type 4 only).
18 - APPENDIX J - METHOD OF TEST FOR JOINT SEPARATION (TYPE 3 ONLY)
18 - J1 SCOPE.
18 - J2 PRINCIPLE.
18 - J3 APPARATUS.
18 - J4 PREPARATION OF TEST SPECIMEN.
18 - J5 TEST PROCEDURE.
18 - J6 REPORT.