• There are no items in your cart

AS 4087-1996

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Metallic flanges for waterworks purposes
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

06-30-2017

Published date

06-05-1996

Preview

1 - AS 4087:1996 METALLIC FLANGES FOR WATERWORKS PURPOSES
4 - PREFACE
5 - CONTENTS
6 - FOREWORD
7 - SECTION 1 - SCOPE AND GENERAL
7 - 1.1 SCOPE
7 - 1.2 REFERENCED DOCUMENTS
8 - 1.3 DEFINITIONS
8 - 1.4 CONFIGURATION
8 - 1.4.1 General
8 - 1.4.2 Type
9 - 1.4.3 Flange face
9 - 1.5 MARKING
9 - 1.5.1 General
9 - 1.5.2 Size
9 - 1.5.3 Information
11 - SECTION 2 - WORKING AND TEST PRESSURES
12 - SECTION 3 - MATERIALS
13 - SECTION 4 - MANUFACTURING REQUIREMENTS, DIMENSIONS AND TOLERANCES
13 - 4.1 MANUFACTURING METHOD
13 - 4.2 DIMENSIONS AND TOLERANCES
13 - 4.2.1 Thickness of flange
13 - 4.2.2 Outside diameter of flange
13 - 4.2.3 O-ring groove
13 - 4.2.4 Height of raised face
13 - 4.2.5 Diameter of raised face
13 - 4.2.6 Bolt holes
14 - 4.3 CONTACT SURFACES
14 - 4.3.1 General
14 - 4.3.2 Determination of surface roughness
14 - 4.3.3 Tolerances
14 - 4.4 SPOT-FACING AND BACK-FACING OF FLANGES
14 - 4.4.1 Parallelism of bearing surfaces
14 - 4.4.2 Diameter of spot-facing
14 - 4.4.3 Back-facing
14 - 4.4.4 Thickness of flanges after spot-facing or back-facing
14 - 4.5 PREPARATION FOR THE ATTACHMENT OF FLANGES
14 - 4.5.1 Screw-on flanges
15 - 4.5.2 Plate flanges
15 - 4.5.2.1 Plate flanges for welding
15 - 4.5.2.2 Plate flanges for brazing
16 - APPENDIX A - PURCHASING GUIDELINES
16 - A1 GENERAL
16 - A2 INFORMATION TO BE SUPPLIEDBY THE PURCHASER
16 - A3 INFORMATION TO BE SUPPLIED BY THE MANUFACTURER
17 - APPENDIX B - DIMENSIONS OF FLANGES
17 - B1 SCOPE
17 - B2 DIMENSIONS
27 - APPENDIX C - SELECTION OF BOLTING
27 - C1 SCOPE
27 - C2 BOLTING
27 - C3 SELECTION OF STUDBOLTS
27 - C4 GALVANIZED COATING
28 - APPENDIX D - ASSEMBLY OF FLANGED JOINTS
28 - D1 SCOPE
28 - D2 FLANGE FACES
28 - D3 GASKETS
28 - D3.1 Selection
28 - D3.2 Material
28 - D3.3 Dimensions
28 - D4 O-RINGS (ELASTOMERIC TOROIDAL SEALS)
28 - D4.1 Material
28 - D4.2 Method of manufacture
28 - D4.3 Dimensions
28 - D4.4 Assembly
28 - D5 BOLTING
29 - D6 TESTING
29 - D6.1 Flanges
29 - D6.2 Flanged joints

Specifies flanges principally intended for waterworks purposes, with working and test pressures for Classes 14, 16, 21 or 35 at temperatures not exceeding 80 degrees Celsius, that have bolting details compatible with the appropriate table of AS 2129. Dimensions are given for copper alloy plate and integral without neck flanges, ductile cast iron screw-on and integral with neck flanges, grey cast iron integral with neck (for pipe fittings) and integral without neck (for other than pipe fittings) flanges and steel blank, plate and integral without neck flanges for ranges of DN (nominal size) and class. Specifies grades of material and requirements for selection of bolting and assembly of flanged joints.

This Standard specifies requirements for circular flanges manufactured from copper alloy, ductile cast iron, grey cast iron, or steel. It covers nominal sizes (see Table 2.1) with pressure ratings for Classes 14, 16, 21 or 35 at temperatures not exceeding 80C. The flanges are for use on pipes, pipe fittings, valves and other equipment that are primarily intended for the conveyance or storage of water or wastewater. NOTE: Guidelines to purchasers on information that should be supplied at the time of enquiry ororder are detailed in Appendix A.

Committee
WS-022
DocumentType
Standard
ISBN
0 7337 0458 1
Pages
23
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

Amendment 1 to AS 4087-1996 see DR 96572 First published as AS 4087-1993.Second edition 1996. First published as AS 4087-1993. Second edition 1996.

AS 1112-1980 ISO metric hexagon nuts, including thin nuts, slotted nuts and castle nuts
AS/NZS 2280:1999 Ductile iron pressure pipes and fittings
AS 1214-1983 Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series)
AS 1831-1985 Iron castings - Spheroidal or nodular graphite cast iron
AS 2129-1994 Flanges for pipes, valves and fittings
AS/NZS 4331.3:1995 Metallic flanges Copper alloy and composite flanges (Reconfirmed 2020)
AS 1646-1992 Elastomeric seals for waterworks purposes
AS 2382-1981 Surface roughness comparison specimens
AS 2536-1982 Surface texture
AS 2528-1982 Bolts, studbolts and nuts for flanges and other high and low temperature applications
AS/NZS 4331.2:1995 Metallic flanges Cast iron flanges (Reconfirmed 2020)
AS 1830-1986 Iron castings - Grey cast iron
AS 1111-1980 ISO metric hexagon commercial bolts and screws
AS 1565-1996 Copper and copper alloys - Ingots and castings (Reconfirmed 2020)
AS/NZS 4331.1:1995 Metallic flanges Steel flanges (Reconfirmed 2020)
AS 3855-1994 Suitability of plumbing and water distribution systems products for contact with potable water
AS 2074-1982 Steel castings
AS 1449-1994 Wrought alloy steels - Stainless and heat-resisting steel plate, sheet and strip
AS 3678-1990 Structural steel - Hot-rolled plates, floorplates and slabs

AS 2845.1-1995 Water supply - Backflow prevention devices - Materials, design and performance requirements
AS/NZS 4766(INT):2002 Polyethylene storage tanks for water and chemicals
AS 4181-1999 Stainless steel clamps for waterworks purposes
AS 3565.1-2004 Meters for water supply Cold water meters
AS 4181-1994 Stainless steel clamps for waterworks purposes
AS 3565.1-1998 Meters for cold potable water - Volumetric chamber and turbine meters
AS 3565.2-1996 Meters for cold potable water - Combination meters
ATS 5200.020-2004 Technical Specification for plumbing and drainage products Flushing valves for water closets and urinals - for use with mains supply
AS 1579-1993 Arc welded steel pipes and fittings for water and waste water
ATS 5200.464-2004 Technical Specification for plumbing and drainage products - Hot water manual or sensor-activated pumping systems
AS/NZS 3500.4:2003 Plumbing and drainage Heated water services
AS/NZS 3500.2:2003 Plumbing and drainage Sanitary plumbing and drainage
AS/NZS 2544:1995 Grey iron pressure fittings
AS 3565.2-2004 Meters for water supply - Combination meters
AS 4809-2003 Copper pipe and fittings - Installation and commissioning
AS/NZS 3500.3:2003 Plumbing and drainage Stormwater drainage
AS/NZS 3518:2004 Acrylonitrile butadiene styrene (ABS) compounds, pipes and fittings for pressure applications
AS 2638.2-1999 Sluice valves for waterworks purposes - Resilient seated
MP 52-1997 Manual of authorization procedures for plumbing and drainage products
AS 1628-1994 Water supply - Copper alloy gate, globe and non-return valves
AS 4795-2002 Double-flanged butterfly valves for waterworks purposes
ATS 5200.021-2004 Technical Specification for plumbing and drainage products Flushing valves for water closets and urinals - for use with break tank supply
ATS 5200.466-2004 Technical Specification for plumbing and drainage products - Rainwater tank connection devices
AS/NZS 2280:2004 Ductile iron pipes and fittings
AS 6401-2003 Knife-gate valves for waterworks purposes (Reconfirmed 2015)
AS 3497-1994 Authorization requirements for plumbing products - Domestic type water treatment appliances
AS 2638.1-2002 Gate valves for waterworks purposes Metal seated
AS 2129-1994 Flanges for pipes, valves and fittings
AS/NZS 2280:1995 Ductile iron pressure pipes and fittings
AS/NZS 2845.1:1998 Water supply - Backflow prevention devices Materials, design and performance requirements
AS 3565.1-1994 Meters for cold potable water - Volumetric chamber and turbine meters
AS/NZS 3497:1998 Drinking water treatment units - Plumbing requirements
AS 1210-1997 Pressure vessels
MP 52-2001 Manual of authorization procedures for plumbing and drainage products
AS 2638.2-2002 Gate valves for waterworks purposes - Resilient seated
AS 3952-2002 Water supply - Spring hydrant valve for waterworks purposes (Reconfirmed 2015)
AS 3578-1993 Cast iron non-return valves for general purposes
AS 2638.1-1999 Sluice valves for waterworks purposes - Metal seated
AS 3565.3-2004 Meters for water supply - Water meters with integral dual check valves
AS/NZS 3500.1:2003 Plumbing and drainage Water services
AS/NZS 2566.2:2002 Buried flexible pipelines Installation (Reconfirmed 2016)
AS 4794-2001 Non-return valves for waterworks purposes - Swing check and tilting disc (Reconfirmed 2015)
AS/NZS 2280:1999 Ductile iron pressure pipes and fittings
AS 1579-2001 Arc-welded steel pipes and fittings for water and wastewater (Reconfirmed 2018)
AS/NZS 3500.3.2:1998 National plumbing and drainage Stormwater drainage - Acceptable solutions

View more information
US$60.92
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.