• There are no items in your cart

AS 60068.2.6-2003

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Environmental testing Tests - Test Fc: Vibration (sinusoidal) (Reconfirmed 2018)
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

05-09-2023

Language(s)

English

Published date

03-20-2003

Preview

1 - AS 60068.2.6-2003 ENVIRONMENTAL TESTING - TESTS-TEST Fc: VIBRATION (SINUSOIDAL)
4 - PREFACE
5 - CONTENTS
7 - 1 Scope
7 - 2 Normative references
8 - 3 Definitions
8 - 3.1 fixing point:
8 - 3.2 measuring points:
9 - 3.2.1 check point:
9 - 3.2.2 reference point:
9 - 3.3 Control points
9 - 3.3.1 single point control:
9 - 3.3.2 multipoint control:
9 - 3.4 sweep cycle:
9 - 3.5 signal tolerance:
9 - 3.6 basic motion:
9 - 3.7 actual motion:
9 - 3.8 damping:
10 - 3.9 critical frequencies:
10 - 3.10 centred resonance frequency:
10 - 3.11 restricted frequency sweeping:
10 - 3.12 gn :
10 - 4 Requirements for testing
10 - 4.1 Required characteristics
10 - 4.1.1 Basic motion
10 - 4.1.2 Spurious motion
11 - 4.1.3 Signal tolerance
11 - 4.1.4 Vibration amplitude tolerances
12 - 4.1.5 Frequency tolerances
12 - 4.1.6 Sweep
12 - 4.2 Mounting
12 - 5 Severities
13 - 5.1 Frequency range
14 - 5.2 Vibration amplitude
15 - 5.3 Duration of endurance
15 - 5.3.1 Endurance by sweeping
16 - 5.3.2 Endurance at fixed frequencies
16 - 6 Preconditioning
16 - 7 Initial measurements
16 - 8 Testing
17 - 8.1 Vibration response investigation
17 - 8.2 Endurance procedures
17 - 8.2.1 Endurance by sweeping
17 - 8.2.2 Endurance at fixed frequencies
18 - 9 Intermediate measurements
18 - 10 Recovery
18 - 11 Final measurements
18 - 12 Information to be given in the relevant specification
20 - Annex A - Guide to test Fc
20 - A.1 Introduction
21 - A.2 Measurement and control
23 - A.3 Testing procedures
25 - A.4 Test severities (see clause 5)
29 - A.5 Equipment normally used with vibration isolators
30 - A.6 Duration
30 - A.7 Dynamic response
31 - A.8 Performance evaluation
31 - A.9 Initial and final measurements
32 - Annex B - Examples of severities primarily intended for components
33 - Annex C - Examples of severities primarily intended for equipment

This Standard gives a method of test to determine the ability of components, equipment and other articles, to withstand specified severities of sinusoidal vibration. The purpose of this test is to determine any mechanical weakness and/or degradation in the specified performance of specimens.

This part of IEC 60068 gives a method of test which provides a standard procedure to determine the ability of components, equipment and other articles, hereinafter referred to as specimens, to withstand specified severities of sinusoidal vibration. The purpose of this test is to determine any mechanical weakness and/or degradation in the specified performance of specimens and to use this information, in conjunction with the relevant specification, to decide the acceptability of the specimens. In some cases, the test method may also be used to demonstrate the mechanical robustness of specimens and/or to study their dynamic behaviour. Categorization of components can also be made on the basis of a selection from within the severities quoted in the test.

Committee
EL-026
DocumentType
Standard
ISBN
0 7337 5084 2
Pages
32
ProductNote
Reconfirmation Notice 14/09/2018 Reconfirmed 14/09/2018.
This standard has been reconfirmed in Australia in 2018 and remains current in New Zealand.
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
IEC 60068-2-6:1995/COR1:1995 Identical
IEC 60068-2-6:2007 Identical
IEC 60068-2-6:1995 Identical

First published as AS 60068.2.6-2003.
Reconfirmed 2018. First published as AS 60068.2.6-2003.

AS 62052.11-2005 Electricity metering equipment (AC) - General requirements, tests and test conditions Metering equipment (IEC 62052-11, Ed.1.0 (2003) MOD)
AS 4428.4:2016 Fire detection, warning, control and intercom systems - Control and indicating equipment Emergency intercom control and indicating equipment
AS 62052.21-2006 Electricity metering equipment (ac) - General requirements, tests and test conditions Tariff and load control equipment (IEC 62052-21, Ed. 1.0 (2004) MOD)
AS ISO 16003-2010 Components for fire extinguishing systems using gas - Requirements and test methods - Container valve assemblies and their actuators; selector valves and their actuators; nozzles; flexible and rigid connectors; and check valves and non-return valves (Reconfirmed 2023)
AS/NZS 1158.6:2010 Lighting for roads and public spaces Luminaires
AS 5062:2016 Fire protection for mobile and transportable equipment
AS 60118.7-2007 Hearing aids Measurement of the performance characteristics of hearing aids for production, supply and delivery quality assurance purposes (Reconfirmed 2019)
AS 60118.9-2007 Hearing aids Methods of measurement of characteristics of hearing aids with bone vibrator output (Reconfirmed 2019)
AS 60947.5.2-2004 Low-voltage switchgear and controlgear Control circuit devices and switching elements - Proximity switches
AS 60947.5.1-2004 Low-voltage switchgear and controlgear Control circuit devices and switching elements - Electromechanical control circuit devices
AS 1603.11-2010 Automatic fire detection and alarm systems Visual warning devices
AS 7240.22-2008 Fire detection and alarm systems Smoke-detection equipment for ducts (ISO 7240-22:2007, MOD)
AS 2144:2014 Traffic signal lanterns
AS/NZS 61000.4.7:2012 Electromagnetic compatibility (EMC) Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto (Reconfirmed 2023)
AS 7240.8-2007 Fire detection and alarm systems Carbon monoxide fire detectors using an electro-chemical cell in combination with a heat sensor
AS/NZS 60065:2003 Audio, video and similar electronic apparatus - Safety requirements (IEC 60065:2001, MOD)
AS 62103-2006 Electronic equipment for use in power installations
AS 2067-2008 Substations and high voltage installations exceeding 1 kV a.c.
AS 60947.5.4-2004 Low-voltage switchgear and controlgear Control circuit devices and switching elements - Methods of assessing the performance of low-energy contacts - Special tests
AS 7240.6-2006 Fire detection and alarm systems Carbon monoxide fire detectors using electro-chemical cells (Reconfirmed 2016)
AS/NZS 60065:2012 Audio, video and similar electronic apparatus - Safety requirements (IEC 60065, Ed.7.2 (2011) MOD)
AS 7240.21-2006 Fire detection and alarm systems - Routing equipment
AS 5062-2006 Fire protection for mobile and transportable equipment
AS 7240.11-2008 Fire detection and alarm systems Manual call points (ISO 7240-11:2005, MOD)
AS 2578-2009 Traffic signal controllers
AS IEC 61800.5.1-2013 Adjustable speed electrical power drive systems Safety requirements - Electrical, thermal and energy
AS 7240.10-2007 Fire detection and alarm systems Point-type flame detectors
AS/NZS 60079.7:2006 Explosive atmospheres Equipment protection by increased safety 'e'
AS/NZS 1158.6:2004 Lighting for roads and public spaces Luminaires
AS 1603.3:2018 Automatic fire detection and alarm systems Heat alarms
AS 2650-2005 Common specifications for high-voltage switchgear and controlgear standards (IEC 60694 Ed.2.2(2002) MOD)
AS IEC 61131.2-2004 Programmable controllers - Equipment requirements and tests
AS 62271.1-2012 High-voltage switchgear and controlgear - Common specifications

View more information
US$78.74
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.