1 - AS ISO/IEC 18000.3-2007 Information technology - Radio frequency identification for item management - Parameters for air interface communications at 13.56 MHz
4 - PREFACE
5 - CONTENTS
7 - INTRODUCTION
9 - 1 Scope
9 - 2 Conformance
9 - 2.1 Claiming conformance
9 - 3 Normative references
10 - 4 Terms and definitions
10 - 5 Symbols and abbreviated terms
10 - 6 Requirements: Physical layer, collision management system and protocol values for 13,56 MHz systems
10 - 6.0 General and applicable to both Modes of this part of ISO/IEC 18000
10 - 6.0.1 Presentation as determined in ISO/IEC 18000-1
10 - 6.0.2 ISO/IEC 18000-3 Interoperability
11 - 6.0.3 ISO/IEC 18000-3 reader conformance/compliance
11 - 6.0.4 ISO/IEC 18000-3 tag compliance.
11 - 6.0.5 Command structure and extensibility
11 - 6.0.6 Mandatory commands
11 - 6.0.7 Optional commands
11 - 6.0.8 Custom commands
11 - 6.0.9 Proprietary commands
12 - 6.1 Physical layer, collision management system and protocols for MODE 1 of this part of ISO/ IEC 18000
12 - 6.1.1 Read/Write system
12 - 6.1.2 Normative Aspects
12 - 6.1.3 Conformance and performance measurement aspects
12 - 6.1.4 Physical Layer
12 - 6.1.5 Protocol and collision management operating method
12 - 6.1.6 Commands
12 - 6.1.7 Parameter tables for interrogator to tag link..
12 - 6.1.8 Parameter tables for tag to interrogator link
12 - 6.1.9 Protocol extension
13 - 6.1.10 Protocol extension- description of collision management method
27 - 6.1.11 Protocol extension commands
37 - 6.1.12 Air interface application laye
38 - 6.2 MODE 2: Physical layer, collision management system and protocols for MODE 2 of this part of ISO/IEC 18000
38 - 6.2.1 Normative aspects: physical and media access control (MAC) parameters: interrogator to tag link
40 - 6.2.2 Tag to interrogator link
43 - 6.2.3 Description of operating method
49 - 6.2.4 Protocol parameters
49 - 6.2.5 Description of protocol operating method
65 - 6.2.6 Collision management parameters
65 - 6.2.7 Description of collision management parameters operating method (informative)
73 - 6.2.8 Tag order sequencing
73 - 6.2.9 Commands
73 - 6.2.10 Air interface application layer
73 - 7 Marking of equipment
74 - 8 Table of characteristic differences between the MODES specified in this part of ISO/ IEC 18000
75 - Annex A (normative) Phase jitter modulation (PJM)
79 - Annex B (informative) Known possible interferences between the MODES determined in this part of ISO/IEC 18000
80 - Annex C (informative) Interrogator pseudo-code for collision management (Mode 1)
81 - Annex D (informative) Cyclic Redundancy Check (CRC) (16 bit)
83 - Annex E (informative) Cyclic redundancy check (CRC) mode 2 (32 bit)
86 - Annex F (informative) Mode 1 IC reference
87 - Annex G (informative) A description of ISO/IEC 15693 Protocol as used in MODE 1
153 - Bibliography