• There are no items in your cart

ASTM A 1090/A1090M : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Forged Rings and Hollows for Use as Base Plates in Power Transmission Structures
Available format(s)

Hardcopy , PDF

Superseded date

03-14-2024

Language(s)

English

Published date

06-06-2019

This specification covers high-strength, low-alloy steel ring and hollow forgings intended primarily for use as base plates in welded tubular structures for power transmission applications.

1.1This specification covers high-strength, low-alloy steel ring and hollow forgings intended primarily for use as base plates in welded tubular structures for power transmission applications. However, use of this specification is not restricted to such applications and it may be used in other applications for which the attributes of the materials, as defined by this specification, are appropriate.

1.2The atmospheric corrosion resistance of Grades A, B, and C in most environments is substantially better than that of carbon structural steel with or without copper addition (see Note 1). When exposed to the atmosphere, these grades are suitable for many applications in the bare (unpainted) condition.

Note 1:See Guide G101 for methods of estimating the atmospheric corrosion resistance of low-alloy steels.

1.3The thickness of forgings is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the thickness of forgings furnished under this specification to a range of 2 to 6 in. [51 to 152 mm].

Note 2:When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service should be used. See Appendix X3 of Specification A6/A6M for information on weldability.

1.4The text of this specification contains notes, footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

1.5Supplementary requirements are available but shall apply only when specified by the purchaser at the time of ordering.

1.6The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
A 01
DocumentType
Standard
Pages
3
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM A 370 : 2021 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 1058 : 2014 Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 6/A6M : 2022 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
ASTM A 1058 : 2012 : REV A Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 1058 : 2019 Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 788/A788M : 2022 Standard Specification for Steel Forgings, General Requirements
ASTM A 788/A788M : 2023 Standard Specification for Steel Forgings, General Requirements
ASTM A 6/A6M : 2019 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
ASTM A 1058 : 2008 Standard Test Methods for Mechanical Testing of Steel Products<span class='unicode'>—</span>Metric
ASTM A 6/A6M : 2023 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
ASTM A 370 : 2020 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 1058 : 2012 Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 1058 : 2012 : REV B Standard Test Methods for Mechanical Testing of Steel Products—Metric
ASTM A 370 : 2023 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 788/A788M : 2019 : REV A Standard Specification for Steel Forgings, General Requirements
ASTM A 6/A6M : 2021 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
ASTM A 370 : 2011 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 370 : 2022 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 788/A788M : 2022 : REV A Standard Specification for Steel Forgings, General Requirements
ASTM A 1058 : 2009 Standard Test Methods for Mechanical Testing of Steel Products<char: emdash>Metric
ASTM E 112 : 2013 : R2021 Standard Test Methods for Determining Average Grain Size
ASTM E 112 : 2013 Standard Test Methods for Determining Average Grain Size

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.