• There are no items in your cart

ASTM A 1094/A1094M : 2020

Current
Current

The latest, up-to-date edition.

Standard Specification for Continuous Hot-Dip Galvanized Steel Bars for Concrete Reinforcement
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

09-09-2020

1.1This specification covers steel reinforcing bars, with protective zinc or zinc-alloy coatings applied by the continuous hot-dip process.

Note 1:The galvanizer is identified throughout this specification as the manufacturer.

1.2Guidelines for construction practices at the job-site are presented in Appendix X1.

1.3Guidelines for use of continuous hot-dip galvanized reinforcing bars with non-galvanized steel forms are presented in Appendix X2.

1.4The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered requirements of the specification.

1.5This specification is applicable for orders in either inch-pound units (as Specification A1094) or SI units (as Specification A1094M).

1.6The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with this specification.

1.7This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
A 01
DocumentType
Standard
Pages
5
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM A 123/A123M : 2017 Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
ASTM A 1055/A1055M : 2016 Standard Specification for Zinc and Epoxy Dual-Coated Steel Reinforcing Bars

ASTM A 615/A615M : 2020 Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
ASTM B 6 : 2018 Standard Specification for Zinc
ASTM A 90/A90M : 2021 Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
ASTM A 90/A90M : 2013 : R2018 Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
ASTM A 706/A706M : 2022 Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
ASTM A 615/A615M : 2022 Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
ASTM A 706/A706M : 2004 Standard Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
ASTM B 852 : 2016 : EDT 1 Standard Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel
ASTM B 6 : 2023 Standard Specification for Zinc
ASTM A 1035/A1035M : 2020 Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement
ASTM A 1035/A1035M : 2023 Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement
ASTM A 1035/A1035M : 2023 : REV A Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement
ASTM A 706/A706M : 2016 Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
ASTM A 706/A706M : 2022 : REV A Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
ASTM B 852 : 2016 : R2022 Standard Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel

View more information
US$63.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.