ASTM B 564 : 2017 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
11-30-2018
English
07-01-2017
1.1This specification2 covers forgings of:
| Alloy Type | UNS Number(s) |
| Fe-Ni-Cr-Mo-N | N08367 |
| Low-carbon Cr-Ni-Fe-N | R20033 |
| Low-carbon Ni-Cr-Mo | N06035, N06058, N06059, N06044 |
| Low-carbon Ni-Cr-Mo-Cu | N06200 |
| Low-carbon Ni-Cr-Mo-W | N06686 |
| Low-carbon Ni-Fe-Cr-Mo-Cu | N08031, N08034 |
| Low-carbon Ni-Mo-Cr | N10276, N06022, N10362 |
| Low-carbon Ni-Mo-Cr-Ta | N06210 |
| Ni | N02200 |
| Ni-Co-Cr-Si | N12160 |
| Ni-Cr-Co-Mo | N06617 |
| Ni-Cr-Fe | N06600, N06603, N06690 |
| Ni-Cr-Fe-Al | N06025 |
| Ni-Cr-Fe-Si | N06045 |
| Ni-Cr-Mo-Nb | N06625 |
| Ni-Cr-Mo-Si | N06219 |
| Ni-Cr-Mo-W | N06110 |
| Ni-Cr-W-Mo | N06230 |
| Ni-Cu | N04400 |
| Ni-Fe-Cr | N08120, N08800, N08810, N08811 |
| Ni-Fe-Cr-Mo-Cu | N08825 |
| Ni-Fe-Cr-W | N06674 |
| Ni-Mo | N10665, N10675, N10629 |
| Ni-Mo-Cr-Fe | N10242, N10624 |
1.1.1The nickel-iron-chromium alloys are UNS N08120, UNS N08800, UNS N08810, and UNS N08811. Alloy UNS N08800 is normally employed in service temperatures up to and including 1100°F (593°C). Alloys UNS N08810, N08120, and UNS N08811 are normally employed in service temperatures above 1100°F (593°C) where resistance to creep and rupture is required, and are annealed to develop controlled grain size for optimum properties in this temperature range.
1.1.2Nickel-iron-chromium-tungsten alloy UNS N06674 is normally employed in service temperatures above 1100°F (593°C) where resistance to creep and rupture is required, and is annealed to develop optimum properties in this temperature range.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health and environmental practices, and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.