• There are no items in your cart

ASTM B 745/B745M : 2015 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains
Available format(s)

PDF

Language(s)

English

Published date

05-18-2015

CONTAINED IN VOL. 02.02, 2016 Specifies corrugated aluminum pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses.

1.1This specification covers corrugated aluminum pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes.

1.2This specification does not include requirements for bedding, backfill, or the relationship between earth-cover load and sheet thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The purchaser must correlate the above factors and also the corrosion and abrasion requirements of the field installation with the sheet thickness. The structural design of corrugated aluminum pipe and the proper installation procedures are given in Practices B790/B790M and B788/B788M, respectively. A procedure for using life-cycle cost analysis techniques to evaluate alternative drainage system designs using corrugated metal pipe is given in Practice A930.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
B 07
DevelopmentNote
Supersedes WW P 402 (C). (08/2004)
DocumentType
Redline
Pages
10
PublisherName
American Society for Testing and Materials
Status
Current

ASTM B 881 : 2017 : REDLINE Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products
ASTM B 788/B788M : 2009 Standard Practice for Installing Factory-Made Corrugated Aluminum Culverts and Storm Sewer Pipe
ASCE/EWRI 12-13, 13-13, 14-13 : 2013 STANDARD GUIDELINES FOR THE DESIGN, INSTALLATION, AND OPERATION AND MAINTENANCE OF URBAN SUBSURFACE DRAINAGE
ASTM B 790/B790M : 2016 : REDLINE Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits
ASTM B 788/B788M : 2009 : R2014 Standard Practice for Installing Factory-Made Corrugated Aluminum Culverts and Storm Sewer Pipe

ASTM F 467M : 2006 : REV A : EDT 2 Standard Specification for Nonferrous Nuts for General Use (Metric)
ASTM B 790/B790M : 2016 : REDLINE Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits
ASTM B 666/B666M : 2015 : REDLINE Standard Practice for Identification Marking of Aluminum and Magnesium Products
ASTM B 744/B744M : 2015 : REDLINE Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe
ASTM F 593 : 2017 : REDLINE Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
ASTM B 209M : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)
ASTM B 221 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
AASHTO T 249 : 2003 METHOD OF TEST FOR HELICAL LOCK SEAM CORRUGATED PIPE
ASTM B 316/B316M : 2015 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods
ASTM A 563 : 2015 : REDLINE Standard Specification for Carbon and Alloy Steel Nuts
ASTM B 209 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
ASTM D 1056 : 2014 : REDLINE Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.