• There are no items in your cart

ASTM C 1265 : 2017 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
Available format(s)

PDF

Superseded date

07-21-2022

Language(s)

English

Published date

09-28-2017

CONTAINED IN VOL. 04.07, 2017 Defines a laboratory procedure for quantitatively measuring the tensile strength, stiffness, and adhesion properties of insulating glass edge seals that are used in structural sealant glazing applications.

1.1This test method covers a laboratory procedure for quantitatively measuring the tensile strength, stiffness, and adhesion properties of insulating glass edge seals that are used in structural sealant glazing applications. Edge seals for these applications use a structural sealant to bond both glass lites and the edge spacer into a monolithic sealed insulating glass unit. In typical applications, the structural sealant acts to hold the outside lite in place under wind and gravity load and to maintain the edge spacer in its proper position. Hereafter, the term “insulating glass” will be abbreviated as “IG.”

1.2The characterization of the IG secondary sealant properties, as defined by this test method, are strongly dependent on glass and edge spacer cleaning procedures, IG spacer profile, location of spacer, and primary IG sealant application. Users of this test method must recognize that the IG edge seal assembly influences the secondary sealant properties.

1.3The values determined by this test method will be characteristic of the particular edge seal assembly that is tested.

Note 1:Presently, only elastomeric, chemically curing silicone sealants specifically formulated for use as the secondary seal of IG units are recognized as having the necessary durability for use in structural sealant glazing applications.

1.4The values stated in SI (metric) units are to be regarded as the standard. The inch-pound values given in parentheses are approximate equivalents, provided for information purposes.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 24
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ISO 20492-3:2010 Glass in buildings — Insulating glass — Part 3: Gas concentration and gas leakage
ISO 28278-1:2011 Glass in building — Glass products for structural sealant glazing — Part 1: Supported and unsupported monolithic and multiple glazing
ASTM C 1294 : 2015 : REDLINE Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM C 1021 : 2008 Standard Practice for Laboratories Engaged in Testing of Building Sealants
ASTM C 1369 : 2007 : R2014 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM C 1021 : 2008 : R2014 Standard Practice for Laboratories Engaged in Testing of Building Sealants
ASTM C 1369 : 2007 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ISO 20492-1:2008 Glass in buildings - Insulating glass — Part 1: Durability of edge seals by climate tests
ASTM C 1193 : 2016 : REDLINE Standard Guide for Use of Joint Sealants
ASTM C 1401 : 2014 : REDLINE Standard Guide for Structural Sealant Glazing
08/30172148 DC : DRAFT MAY 2008 BS ISO 28278-1 - GLASS IN BUILDING - GLASS PRODUCTS FOR STRUCTURAL SEALANT GLAZING - PART 1: SUPPORTED AND UNSUPPORTED MONOLITHIC AND MULTIPLE GLAZING
ISO 20492-2:2008 Glass in buildings - Insulating glass — Part 2: Chemical fogging tests

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.