• There are no items in your cart

ASTM C 157/C157M : 2017 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete
Available format(s)

PDF

Language(s)

English

Published date

08-15-2017

CONTAINED IN VOL. 04.02, 2017 Defines the determination of the length changes that are produced by causes other than externally applied forces and temperature changes in hardened hydrauliccement mortar and concrete specimens made in the laboratory and exposed to controlled conditions of temperature and moisture.

1.1This test method covers the determination of the length changes that are produced by causes other than externally applied forces and temperature changes in hardened hydraulic-cement mortar and concrete specimens made in the laboratory and exposed to controlled conditions of temperature and moisture.

1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E11. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 09
DevelopmentNote
Supersedes ASTM C 157 (07/2006)
DocumentType
Redline
Pages
9
PublisherName
American Society for Testing and Materials
Status
Current

CSA A23.1 A23.2 : 2014 CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE
ASTM C 1709 : 2011 Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete
ACI 360R : 2010 GUIDE TO DESIGN OF SLABS-ON-GROUND
ASTM C 928/C928M : 2013 : REDLINE Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs
ACI 325.14R : 2017 GUIDE FOR DESIGN AND PROPORTIONING OF CONCRETE MIXTURES FOR PAVEMENTS
ASTM C 596 : 2009 : R2017 Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement
ASTM C 1708/C1708M : 2016 : REDLINE Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements
ASTM C 1293 : 2008 : REV B : R2015 Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction
S6.1-14 Commentary on S6-14, Canadian Highway Bridge Design Code
ASTM C 1582/C1582M : 2011 : R2017 : EDT 1 Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete
ASTM C 1293 : 2008 : REV A Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction
ASTM C 1698 : 2009 Standard Test Method for Autogenous Strain of Cement Paste and Mortar
ASTM C 1107/C1107M : 2017 : REDLINE Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
AASHTO TP 96 : 2013 (R2018) METHOD OF TEST FOR PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE
AASHTO TP 110 : 2014 METHOD OF TEST FOR POTENTIAL ALKALI REACTIVITY OF AGGREGATES AND EFFECTIVENESS OF ASR MITIGATION MEASURES (MINIATURE CONCRETE PRISM TEST, MCPT)
ASTM C 596 : 2009 Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement
MIL-DTL-32536 Base Document:2015 CONCRETE CAPPING MATERIAL, RAPID SETTING
ASTM C 596 : 2009 : EDT 1 Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement
ACI 351.1R : 2012 REPORT ON GROUTING BETWEEN FOUNDATIONS AND BASES FOR SUPPORT OF EQUIPMENT & MACHINERY
ACI 301 : 2016 SPECIFICATIONS FOR STRUCTURAL CONCRETE
ACI SP 307 : 2016 SHRINKAGE COMPENSATING CONCRETE - PAST, PRESENT, AND FUTURE
ASTM C 183/C183M : 2016 : REDLINE Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
ASTM C 1105 : 2008 : REV A : R2016 Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction
ASTM C 330 : 2005 Standard Specification for Lightweight Aggregates for Structural Concrete
ASTM C 331/C331M : 2017 : REDLINE Standard Specification for Lightweight Aggregates for Concrete Masonry Units
ASTM C 331 : 2005 Standard Specification for Lightweight Aggregates for Concrete Masonry Units
ASTM C 1107 : 2007 SPECIFICATION FOR PACKAGED DRY, HYDRAULIC-CEMENT GROUT (NONSHRINK)
ASTM C 1148 : 1992 : REV A : R1997 : EDT 1 Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar
ASTM C 1622/C1622M : 2010 : R2016 : EDT 1 Standard Specification for Cold-Weather Admixture Systems
ASTM C 1148 : 1992 : REV A : R2014 Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar (Withdrawn 2019)
UFC 3-301-01 : Change 3 UNIFIED FACILITIES CRITERIA - STRUCTURAL ENGINEERING
ASTM C 1148 : 1992 : REV A : R2008 Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar
ACI 301M : 2016 SPECIFICATIONS FOR STRUCTURAL CONCRETE
ACI 303R : 2012 GUIDE TO CAST-IN-PLACE ARCHITECTURAL CONCRETE PRACTICE
ACI 364.3R : 2009 GUIDE FOR CEMENTITIOUS REPAIR MATERIAL DATA SHEET
ACI ITG-8R : 2010 REPORT ON PERFORMANCE-BASED REQUIREMENTS FOR CONCRETE
ACI 223R : 2010 GUIDE FOR THE USE OF SHRINKAGE-COMPENSATING CONCRETE
AASHTO T 127 : 2015 METHOD OF TEST FOR SAMPLING AND AMOUNT OF TESTING OF HYDRAULIC CEMENT
ASTM C 1792 : 2014 Standard Test Method for Measurement of Mass Loss versus Time for One-Dimensional Drying of Saturated Concretes (Withdrawn 2023)
ASTM C 1856/C1856M : 2017 Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete
ASTM C 1698 : 2009 : R2014 Standard Test Method for Autogenous Strain of Cement Paste and Mortar
ASTM C 494/C494M : 2017 : REDLINE Standard Specification for Chemical Admixtures for Concrete
ASTM C 1731 : 2016 : REDLINE Standard Specification for Concrete Floor Tile
ASTM C 1105 : 2008 Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction
ASTM C 1622/C1622M : 2010 Standard Specification for Cold-Weather Admixture Systems
AASHTO TP 96 : 2013 METHOD OF TEST FOR PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE
ASTM C 688 : 2014 : REDLINE Standard Specification for Functional Additions for Use in Hydraulic Cements
ASTM C 1293 : 2008 : REV B Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction
ACI PRC-506 : 2016 GUIDE TO SHOTCRETE
UFC 4-150-07 : Change 1 UNIFIED FACILITIES CRITERIA - MAINTENANCE AND OPERATION: MAINTENANCE OF WATERFRONT FACILITIES
ACI 237R : 2007 SELF-CONSOLIDATING CONCRETE
CSA A3000 : 2013 CEMENTITIOUS MATERIALS COMPENDIUM
ASTM C 1012 : 2004 Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
ASTM C 806 : 2013-02 TEST METHOD FOR RESTRAINED EXPANSION OF EXPANSIVE CEMENT MORTAR
ASTM C 1148 : 1992 : REV A : R2002 Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar
ASTM C 1105 : 2008 : REV A Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction
ASTM C 666/C666M : 2015 : REDLINE Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing
ASTM C 1582/C1582M : 2011 Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete
ACI 330.2R:2017(R2023) Guide for the Design and Construction of Concrete Site Paving for Industrial and Trucking Facilities

ASTM C 1437 : 2015 : REDLINE Standard Test Method for Flow of Hydraulic Cement Mortar
ASTM C 305 : 2014 : REDLINE Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
ASTM C 192/C192M : 2016-04 PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY
ASTM E 337 : 2015 : REDLINE Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASTM E 11 : 2017 : REDLINE Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.