Standard Specification for Mineral Fiber Thermal Insulating Cement

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

03-01-2019

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 04.06, 2014 Defines mineral fiber thermal insulating materials in the form of dry cement, which, when mixed with a suitable proportion of water, applied as a plastic mass, and dried in place, affords resistance to heat transmission on surfaces operating at temperatures between 250 and 1900 degrees F (about 121 and 1038 degrees C).

1.1This specification covers mineral fiber thermal insulating materials in the form of dry cement, which, when mixed with a suitable proportion of water, applied as a plastic mass, and dried in place, affords resistance to heat transmission on surfaces operating at temperatures between 250 and 1900°F (about 121 and 1038°C).

1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	C 16
DevelopmentNote	Supersedes MIL C 2908 (B). (09/2010)
DocumentType	Standard
Pages	3
ProductNote	Reconfirmed 2007 THIS STANDARD ALSO REFERS TO ASTM E 136
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM C 195 : 2000 ASTM C 195 : 2007 : R2013

ASTM E 136 : 2024	Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 °C
ASTM C 168 : 2019	Standard Terminology Relating to Thermal Insulation
ASTM C 1045 : 2019	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
ASTM C 177 : 2019	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
ASTM C 1114 : 2006 : R2013	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
ASTM C 1114 : 2006 : R2019	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
ASTM C 1045 : 2007 : R2013	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
ASTM C 518 : 2017 : REDLINE	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM C 163 : 2005 : R2023	Standard Practice for Mixing Thermal Insulating Cement Samples
ASTM C 356 : 2022	Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
ASTM C 163 : 2005 : R2016	Standard Practice for Mixing Thermal Insulating Cement Samples
ASTM C 1058 : 1997	Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
ASTM E 136 : 2022	Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 °C
ASTM C 1058 : 2003	Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
ASTM C 390 : 2008 : R2024	Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
ASTM C 1114 : 2006	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
ASTM E 136 : 2019 : REV A	Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750°C
ASTM C 1045 : 2001	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
ASTM C 518 : 2002	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM C 390 : 2008 : R2019	Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
ASTM C 356 : 2017	Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
ASTM C 411 : 2019	Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
ASTM C 356 : 2017 : REDLINE	Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
ASTM C 1114 : 2000	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
ASTM C 136 : 2006	Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
ASTM C 518 : 2017	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM C 166 : 2005 : R2023	Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement
ASTM C 518 : 2021	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM C 1114 : 2000 : R2006	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
ASTM C 1045 : 1997	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
ASTM C 166 : 2005 : R2016	Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement
ASTM C 177 : 2019 : EDT 1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
ASTM C 168 : 2022	Standard Terminology Relating to Thermal Insulation
ASTM C 136 : 1996	Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
ASTM C 1058 : 2003 : R2008	Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
ASTM E 136 : 2024 : REV A	Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 °C
ASTM C 1045 : 2007	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
ASTM C 1058/C1058M : 2010 : R2015	Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
ASTM C 518 : 1998	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus