• There are no items in your cart

ASTM C 230/C230M : 2020

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Flow Table for Use in Tests of Hydraulic Cement
Available format(s)

Hardcopy , PDF

Superseded date

06-09-2023

Language(s)

English

Published date

07-17-2020

1.1This specification covers requirements for the flow table and accessory apparatus (Note 1) used in making flow tests for consistency of mortars in tests of hydraulic cement, such as but not limited to Test Method C1437.

Note 1:To help clarify the design of the flow table and accessory apparatus see the drawing in Fig. 1 [Fig. 2]. This drawing is for informational purposes only.

FIG. 1Flow Table and Accessory Apparatus (Partial) (IP)

Flow Table and Accessory Apparatus (Partial) (IP)Flow Table and Accessory Apparatus (Partial) (IP)

FIG. 1Flow Table and Accessory Apparatus (Partial) (IP) (continued)

Flow Table and Accessory Apparatus (Partial) (IP)Flow Table and Accessory Apparatus (Partial) (IP)

FIG. 2Flow Table and Accessory Apparatus (Partial) [SI]

Flow Table and Accessory Apparatus (Partial) [SI]Flow Table and Accessory Apparatus (Partial) [SI]

FIG. 2Flow Table and Accessory Apparatus (Partial) [SI] (continued)

Flow Table and Accessory Apparatus (Partial) [SI]Flow Table and Accessory Apparatus (Partial) [SI]

FIG. 2Flow Table and Accessory Apparatus (Partial) [SI] (continued)

Flow Table and Accessory Apparatus (Partial) [SI]Flow Table and Accessory Apparatus (Partial) [SI]

1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. It is permissible to use an inch-pound caliper and mold with a SI flow table or a SI caliper and mold with an inch-pound flow table. It is not permissible to mix a SI mold with an inch-pound caliper or an inch-pound mold with a SI caliper.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 01
DocumentType
Standard
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 1856/C1856M : 2017 Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete
ASTM C 141/C141M : 2014 Standard Specification for Hydrated Hydraulic Lime for Structural Purposes
ASTM C 1446 : 2019 Standard Test Method for Measuring Consistency of Self-Flowing Castable Refractories
ASTM C 452 : 2019 : EDT 1 Standard Test Method for Potential Expansion of Portland-Cement<brk/> Mortars Exposed to Sulfate
ASTM C 1093 : 2019 Standard Practice for Accreditation of Testing Agencies for Masonry
ASTM C 219 : 2020 : REV A Standard Terminology Relating to Hydraulic and Other Inorganic Cements
ASTM C 1072 : 2019 Standard Test Methods for Measurement of Masonry Flexural Bond Strength
ASTM C 1437 : 2020 Standard Test Method for Flow of Hydraulic Cement Mortar
ASTM D 1734 : 1993 : R2013 Standard Practice for Making Cementitious Panels for Testing Coatings
ASTM C 1445 : 2013 : R2018 Standard Test Method for Measuring Consistency of Castable Refractory Using a Flow Table
ASTM C 156 : 2020 Standard Test Method for Water Loss [from a Mortar Specimen] Through Liquid Membrane-Forming Curing Compounds for Concrete
ASTM C 109/C109M : 2020 : REV B Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens)
ASTM C 87/C87M : 2017 Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar
ASTM C 1506 : 2017 Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters
ASTM C 185 : 2020 Standard Test Method for Air Content of Hydraulic Cement Mortar
ASTM C 110 : 2020 Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone
ASTM C 348 : 2020 Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.