• There are no items in your cart

ASTM C 979 : 2005

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Pigments for Integrally Colored Concrete
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

01-01-2005

CONTAINED IN VOL. 04.02, 2005 Outlines prerequisites for colored and white pigments in powder form used as admixtures in concrete for making integrally colored concrete.

1.1 This specification covers the basic requirement for colored and white pigments in powder form to be used as admixtures in concrete for the purpose of producing integrally colored concrete. Where the pigments are a constituent of a multicomponent admixture, this specification applies to the pigment constituent of the admixture. This specification is not intended to establish compatibility of pigments with any other concrete admixtures unless they are tested in combination in accordance with .

1.2 This specification does not include the determination of pigment stability when elevated temperature using low-pressure (atmospheric) or high-pressure (autoclave) steam is used to accelerate the curing process.

1.3 In addition to tests defining the pigments themselves, a limited number of tests on concrete are included to define the effects on setting times, air content, and compressive strength. If more extensive information is required for a particular job, additional testing criteria and procedures should be agreed upon between the seller and user.

1.4 The maximum prescribed dosage rate of a pigment, established in accordance with , shall be equal to or less than 10 mass % of cement. When a combination of pigments is used to produce the desired color and color intensity, the total dosage rate of all pigments combined shall not exceed any of the individual maximum dosage rates of the component pigments.

1.5 The values stated in SI units are to be regarded as the standard. The inch-pound units in parentheses are for information purposes only.

Committee
C 09
DocumentType
Standard
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ACI 549.3R : 2009 : R2017 REPORT ON GLASS FIBER-REINFORCED CONCRETE PREMIX
CSA A220 SERIES : 2006 CONCRETE ROOF TILES
CSA A220 SERIES : 2006 : INC : UPD 4 : 2010 : R2012 CONCRETE ROOF TILES
ASTM C 1713 : 2017 : REDLINE Standard Specification for Mortars for the Repair of Historic Masonry
ASTM C 1670 : 2013 Standard Specification for Adhered Manufactured Stone Masonry Veneer (AMSMV) Units
ASTM C 1492 : 2003 : R2016 Standard Specification for Concrete Roof Tile
CSA A231.2 : 0 PRECAST CONCRETE PAVERS
ASTM C 1492 : 2003 Standard Specification for Concrete Roof Tile
ACI 549.3R : 2009 REPORT ON GLASS FIBER-REINFORCED CONCRETE PREMIX
CSA A231.1 : 0 PRECAST CONCRETE PAVING SLABS
ACI 303.1 : 1997 STANDARD SPECIFICATION FOR CAST-IN-PLACE ARCHITECTURAL CONCRETE
ASTM C 1790 : 2015 : REDLINE Standard Specification for Fly Ash Facing Brick
ACI 303R : 2012 GUIDE TO CAST-IN-PLACE ARCHITECTURAL CONCRETE PRACTICE
ASTM C 1732 : 2015 : REDLINE Standard Practice for Installation of Concrete Floor Tiles
CSA A23.1 A23.2 : 2014 CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE
ASTM C 1492 : 2003 : R2009 Standard Specification for Concrete Roof Tile
CSA A220 SERIES : 2006 : INC : UPD 4 : 2010 CONCRETE ROOF TILES
NACE RP 01 87 : 2005 DESIGN CONSIDERATIONS FOR CORROSION CONTROL OF REINFORCING STEEL IN CONCRETE
CSA A220 SERIES : 2006 : R2016 CONCRETE ROOF TILES

ASTM C 403/C403M : 2016 : REDLINE Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance
ACI 211.1 : 1991 SELECTING PROPORTIONS FOR NORMAL, HEAVYWEIGHT AND MASS CONCRETE
ASTM C 192/C192M : 2016-04 PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY
ASTM G 23 : 1996 Practice for Operating Light-Exposure Apparatus (Carbon-Arc Type) With and Without Water for Exposure of Nonmetallic Materials (Withdrawn 2000)

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.