• There are no items in your cart

ASTM D 1120 : 2017 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Boiling Point of Engine Coolants
Available format(s)

PDF

Superseded date

09-28-2022

Language(s)

English

Published date

04-12-2017

CONTAINED IN VOL. 15.05, 2017 Specifies the determination of the equilibrium boiling point of engine coolants.

1.1This test method covers the determination of the equilibrium boiling point of engine coolants. The equilibrium boiling point indicates the temperature at which the sample will start to boil in a cooling system under equilibrium conditions at atmospheric pressure.

Note 1:Engine coolants may also be marketed in a ready-to-use form (prediluted). This test procedure is applicable to diluted solutions as well as to concentrates.

Note 2:The procedure for obtaining a representative test sample of a coolant solution that contains an antileak additive is found in Practice D1176.

1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 15
DocumentType
Redline
Pages
3
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

MIL-A-11755 Revision E:1994 ANTIFREEZE, ARCTIC-TYPE
O-A-548 Revision D:1974 ANTIFREEZE COOLANT, ENGINE, ETHYLENE GLYCOL, INHIBITED, CONCENTRATED
SAE J 814 : 2018 COOLANTS FOR INTERNAL COMBUSTION ENGINES
ASTM D 8085 : 2017 Standard Specification for Non-Aqueous Engine Coolant for Automobile and Light-Duty Service
ASTM D 7518 : 2010 Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service
ASTM D 3306 : 2014-05 SPECIFICATION FOR GLYCOL BASE ENGINE COOLANT FOR AUTOMOBILE AND LIGHT-DUTY SERVICE
ASTM D 7714 : 2011 Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
MIL-STD-883 Revision K:2016 TEST METHOD STANDARD - MICROCIRCUITS
09/30163562 DC : DRAFT SEP 2009 BS 6580 AMD2 - SPECIFICATION FOR CORROSION INHIBITING, ENGINE COOLANT CONCENTRATE ('ANTIFREEZE')
BS AU 174-2:1985 Hydraulic brake systems, using non-petroleum base brake fluids for road vehicles Specification for non-petroleum base brake fluid
SAE J 1704 : 2016 MOTOR VEHICLE BRAKE FLUID BASED UPON GLYCOLS, GLYCOL ETHERS AND THE CORRESPONDING BORATES
ASTM D 4656 : 1998 Standard Specification for Prediluted Aqueous Ethylene Glycol Base Engine Coolant (50 Volume % Minimum) for Automobiles and Light-Duty Service (Withdrawn 2000)
ASTM D 3585 : 2008 Standard Specification for ASTM Reference Fluid for Coolant Tests
ASTM D 3585 : 2008 : R2013 Standard Specification for ASTM Reference Fluid for Coolant Tests
ASTM D 4985 : 2010 Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA)
ASTM D 345 : 2002 Side bearings of the freight wagon bogies. General specifications
ISO 4925:2005 Road vehicles Specification of non-petroleum-base brake fluids for hydraulic systems
BS ISO 4925:2005 Road vehicles. Specification of non-petroleum-base brake fluids for hydraulic systems
03/106442 DC : DRAFT APR 2003 ISO 4925 - ROAD VEHICLES - SPECIFICATION FOR NON-PETROLEUM BASE FLUIDS FOR HYDRAULIC SYSTEMS
ASTM D 5216 : 1998 Standard Specification for Propylene Glycol Base Engine Coolant for Automobile and Light-Duty Service (Withdrawn 2000)
ASTM D 6257 : 1998 Standard Specification for Prediluted Aqueous Propylene Glycol Base Engine Coolant (50 Volume % Minimum) for Automobile and Light-Duty Service (Withdrawn 2000)
ASTM D 5345 : 1998 Standard Specification for Prediluted Aqueous Ethylene Glycol Base Low-Silicate Engine Coolant (50 Volume % Minimum) for Heavy-Duty Engines Requiring an Initial Charge of Supplemental Coolant Additive (SCA) (Withdrawn 2000)
NASA KSC SPEC P 0024 : 2001 REFRIGERANT, HCFC-124, 2-CHLORO-1,1,1,2-TETRAFLUOROETHANE, SPECIFICATION FOR
MIL-STD-750-1 Revision A:2015 Environmental Test Methods for Semiconductor Devices Part 1: Test Methods 1000 Through 1999
BS 6580:2010 Specification for corrosion inhibiting, engine coolant concentrate (\'antifreeze\')
SAE J 1703 : 2016 MOTOR VEHICLE BRAKE FLUID
ASTM D 7714 : 2011 : R2016 : EDT 1 Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
MIL-A-46153 Revision C:1991 ANTIFREEZE, ETHYLENE GLYCOL, INHIBITED, HEAVY DUTY, SINGLE PACKAGE
A-A-59150 Revision A:1998 CLEANING COMPOUND, SOLVENT, HYDROFLUOROETHER (HFE)
ASTM D 7518 : 2010 : R2015 : EDT 1 Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service
ASTM D 4985 : 2010 : R2015 Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA)

ASTM E 1 : 2014 : REDLINE Standard Specification for ASTM Liquid-in-Glass Thermometers
ASTM D 1176 : 2014 : REDLINE Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.