ASTM D 1238 : 2020
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
Available format(s)
Hardcopy , PDF
Superseded date
12-09-2023
Language(s)
English
Published date
09-03-2020
1.1This test method covers the determination of the rate of extrusion of molten thermoplastic resins using an extrusion plastometer.
1.2The values stated in SI units are to be regarded as standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:This standard and ISO 1133 address the same subject matter, but differ in technical content.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
17
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 3935 : 2021 | Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
| ASTM D 3835 : 2016 | Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer |
| ASTM D 2839 : 2016 | Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene |
| ASTM D 2737 : 2022 | Standard Specification for Polyethylene (PE) Plastic Tubing |
| ASTM D 6265 : 2017 | Standard Practice for Separation of Contaminants in Polymers Using an Extruder Filter Test |
| ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3307 : 2021 | Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials |
| ASTM F 3034 : 2021 | Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE) |
| ASTM D 3159 : 2022 | Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials |
| ASTM D 7238 : 2020 | Standard Test Method for Effect of Exposure of Unreinforced Polyolefin Geomembrane Using Fluorescent UV Condensation Apparatus |
| ASTM D 2513 : 2020 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 4565 : 2020 | Standard Test Methods for Physical and Environmental Performance Properties of <brk/>Insulations and Jackets for Telecommunications Wire and Cable |
| ASTM D 3222 : 2021 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
| ASTM F 3219 : 2019 | Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings |
| ASTM F 2389 : 2021 | Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems |
| ASTM D 2239 : 2022 | Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter |
| ASTM D 6339 : 2011 : R2019 | Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS) |
| ASTM D 3350 : 2021 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 2764/F2764M : 2019 | Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4549 : 2015 : R2021 | Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS) |
| ASTM D 5577 : 2019 | Standard Guide for Techniques to Separate and Identify Contaminants in Recycled Plastics |
| ASTM F 3508 : 2021 : REV A | Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT) |
| ASTM D 5422 : 2017 | Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer |
| ASTM D 5675 : 2013 : R2018 | Standard Classification for Low Molecular Weight PTFE and FEP Micronized Powders |
| ASTM D 3485 : 2022 | Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) |
| ASTM F 790 : 2023 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM D 7472 : 2019 | Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials |
| ASTM F 2881/F2881M : 2021 : EDT 1 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F 755 : 2019 | Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants |
| ASTM F 624 : 2009 : R2015 : EDT 1 | Standard Guide for Evaluation of Thermoplastic Polyurethane Solids and Solutions for Biomedical Applications |
| ASTM D 6388 : 2018 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geonets to Liquids |
| ASTM D 3275 : 2018 | Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials |
| ASTM D 4976 : 2012 : REV A : R2020 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 6394 : 2021 : REV A | Standard Classification System for and Basis for Specification for Sulfone Plastics (SP) |
| ASTM F 561 : 2019 | Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids |
| ASTM D 7082 : 2021 | Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe |
| ASTM D 3364 : 1999 : R2019 | Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications |
| ASTM F 2619/F2619M : 2020 | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| ASTM F 997 : 2018 | Standard Specification for Polycarbonate Resin for Medical Applications |
| ASTM D 6434 : 2012 : R2018 | Standard Guide for the Selection of Test Methods for Flexible Polypropylene Geomembranes |
| ASTM D 2116 : 2016 : R2021 | Standard Specification for FEP Resin Molding and Extrusion Materials |
| ASTM D 7471 : 2019 | Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials |
| ASTM D 4203 : 2017 | Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials |
| ASTM F 639 : 2009 : R2015 | Standard Specification for Polyethylene Plastics for Medical Applications |
| ASTM F 714 : 2022 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
| ASTM D 5138 : 2016 | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
| ASTM F 3123 : 2022 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
| ASTM F 3087 : 2015 | Standard Specification for Acrylic Molding Resins for Medical Implant Applications |
| ASTM F 2150 : 2019 | Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Regenerative Medicine and Tissue-Engineered Medical Products |
| ASTM D 5721 : 2022 | Standard Practice for Air-Oven Aging of Polyolefin Geomembranes |
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM F 2435 : 2022 | Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe |
| ASTM D 6389 : 2017 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geotextiles to Liquids |
| ASTM D 3035 : 2022 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 5990 : 2020 : REV A | Standard Classification System and Basis for Polyketone Injection Molding and Extrusion Materials (PK) |
| ASTM D 4635 : 2016 | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 5575 : 2018 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM D 4067 : 2021 | Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods |
| ASTM D 5205 : 2016 | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
| ASTM D 6213 : 2017 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geogrids to Liquids |
| ASTM D 788 : 2016 | Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds |
| ASTM E 456 : 2002 | Standard Terminology for Relating to Quality and Statistics |
| ASTM E 456 : 2013 : REV A : R2022 | Standard Terminology Relating to Quality and Statistics |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 5947 : 2001 : EDT 1 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 6 | Standard Terminology Relating to Quality and Statistics |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
US$83.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.