• There are no items in your cart

ASTM D 1310 : 2014 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
Available format(s)

PDF

Language(s)

English

Published date

12-15-2014

CONTAINED IN VOL. 06.01, 2017 Defines the determination by Tag Open-Cup Apparatus of the flash point and fire point of liquids having flash points between -18 and 165 degrees C (0 and 325 degrees F) and fire points up to 325 degrees F.

1.1This test method covers the determination by Tag Open-Cup Apparatus of the flash point and fire point of liquids having flash points between −18 and 165°C (0 and 325°F) and fire points up to 325°F.

1.2This test method, when applied to paints and resin solutions that tend to skin over or that are very viscous, gives less reproducible results than when applied to solvents.

Note 1:In order to conserve time and sample, the fire point of a material may be determined by the Tag Open-Cup Method by continuing the heating of the specimen to its fire point. Fire points may also be determined by Test Method D92, which should be used for fire points beyond the scope of this test method.

1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors pertinent to an assessment of the fire hazard of a particular end use

1.5Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for details and EPA’s website, http://www.epa.gov/mercury/faq.htm, for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.

1.6This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 01
DocumentType
Redline
Pages
9
PublisherName
American Society for Testing and Materials
Status
Current

MIL-R-46082 Revision B:1983 RETAINING COMPOUNDS, SINGLE COMPONENT, ANAEROBIC
ASTM D 6465 : 1999 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM D 6465 : 1999 : R2016 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM E 502 : 2007 : R2013 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
ASTM C 647 : 2008 Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation
ASTM D 3105 : 2017 : REDLINE Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM D 6465 : 1999 : R2005 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
CEN/TR 15138:2005 Petroleum products and other liquids - Guide to flash point testing
TT-C-621 Revision B:1973 CORRECTION FLUID, DUPLICATING MACHINE STENCIL
CSA Z752 : 2003 : R2013 DEFINITION OF HOUSEHOLD HAZARDOUS WASTE
MIL-C-82594 Base Document:1971 CORROSION PREVENTIVE COMPOUND AND SURFACE SEALER FOR NONFERROUS METALS
ISO/TR 29662:2009 Petroleum products and other liquids Guidance for flash point testing
MIL-L-8937 Revision D:1982 LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING, [NATO CODE NUMBER S 1738]
MIL-DTL-87177 Revision B:2014 LUBRICANTS, CORROSION PREVENTIVE COMPOUND, WATER DISPLACING, SYNTHETIC
NFPA 49 : 1994 HAZARDOUS CHEMICALS DATA
ACI 548.5R : 2016 GUIDE FOR POLYMER CONCRETE OVERLAYS
ASTM D 5958 : 1999 : R2005 : EDT 1 Standard Practices for Preparation of Oil-Based Ink Resin Solutions
ASTM C 647 : 2008 : R2013 Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation
ASTM D 5958 : 1999 : R2011 Standard Practices for Preparation of Oil-Based Ink Resin Solutions
ASTM D 268 : 2001 : R2007 Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material
ASTM E 936 : 1998 : R2004 Standard Practice for Roof System Assemblies Employing Steel Deck, Preformed Roof Insulation, and Bituminous Built-Up Roofing (Withdrawn 2012)
ASTM D 268 : 2001 : R2012 Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material (Withdrawn 2021)
MIL L 87177 : A LUBRICANT, CORROSION PREVENTIVE COMPOUND, WATER DISPLACING, SYNTHETIC
DWA-M 143-20:2018 TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS
ASTM D 4800 : 1994 : R2011 Standard Guide for Classifying and Specifying Adhesives
SAE AMS 3066 : 2016 COMPOUND, CORROSION-INHIBITING WATER-DISPLACING, SOFT FILM, AEROSOL CANNED
ACI 548.10 : 2010 SPECIFICATION FOR TYPE MMS (METHYL METHACRYLATE SLURRY) POLYMER OVERLAYS FOR BRIDGE AND PARKING GARAGE DECKS
ACI SPEC-548.10 : 2010 SPECIFICATION FOR TYPE MMS (METHYL METHACRYLATE SLURRY) POLYMER OVERLAYS FOR BRIDGE AND PARKING GARAGE DECKS
ASTM D 3323 : 1980 : R1988 : EDT 1 Guide for Testing Interior Solvent-Thinned Flat Wall Paints (Withdrawn 1993)
NFPA 921 : 2017 GUIDE FOR FIRE AND EXPLOSION INVESTIGATIONS
NASA STD 6001(INT) : 2009 FLAMMABILITY, OFFGASSING, AND COMPATIBILITY REQUIREMENTS AND TEST PROCEDURES
NASA STD 6001 : 2011 FLAMMABILITY, OFFGASSING, AND COMPATIBILITY REQUIREMENTS AND TEST PROCEDURES
ASTM D 5958 : 1999 : R2012 : EDT 1 Standard Practices for Preparation of Oil-Based Ink Resin Solutions
MIL-PRF-62218 Revision B:1996 CORROSION PREVENTIVE COMPOUNDS, COLD APPLICATION (FOR NEW AND FIELD MOTOR VEHICLES AND TRAILERS)
ASTM E 502 : 2007 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
I.S. CEN/TR 15138:2005 PETROLEUM PRODUCTS AND OTHER LIQUIDS - GUIDE TO FLASH POINT TESTING
ASTM E 502 : 2007 : EDT 1 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
ASTM D 4800 : 1994 : R1999 Standard Guide for Classifying and Specifying Adhesives
ASTM E 936 : 1998 Standard Practice for Roof System Assemblies Employing Steel Deck, Preformed Roof Insulation, and Bituminous Built-Up Roofing
ASTM D 6465 : 1999 : R2012 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
NACE RP0276:1976 EXTRUDED ASPHALT MASTIC TYPE PROTECTIVE COATINGS FOR UNDERGROUND PIPELINES
ASTM D 2336 : 1999 Standard Guide for Specifying Factory Applied Wood Coatings (Withdrawn 2008)
ASTM D 4800 : 1994 : R2005 Standard Guide for Classifying and Specifying Adhesives
VV-D-1078 Revision B:1983 DAMPING FLUID, SILICONE BASE (DIMETHYL POLYSILOXANE)
MIL-C-81947 Revision A:1975 COATING COMPOUND, THERMAL INSULATION, THREE-COMPONENT, INTUMESCENT
PD CEN/TR 15138:2005 Petroleum products and other liquids. Guide to flash point testing
O-A-549 Revision A:1973 ANTI FOGGING COMPOUND
MIL-C-82407 Base Document:1968 COATING, EPOXY, FOR STEEL STRUCTURES
CSA Z752 : 2003 DEFINITION OF HOUSEHOLD HAZARDOUS WASTE
ASTM D 5958 : 1999 Standard Practices for Preparation of Oil-Based Ink Resin Solutions
PPP-P-1892 Base Document:1974 PAINT, VARNISH, LACQUER AND RELATED MATERIALS, PACKAGING, PACKING, AND MARKING OF
MIL-PRF-81298 Revision E:2011 Dye, Liquid for the Detection of Leaks in Aircraft Fuel Systems
SAE J 357 : 2016 PHYSICAL AND CHEMICAL PROPERTIES OF ENGINE OILS
ASTM D 6038 : 2014 : REDLINE Standard Test Methods for Determining the Compatibility of Resin/Solvent Mixtures by Precipitation Temperature (Cloud Point)
ASTM D 268 : 2001 Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material
ASTM D 4800 : 1994 : R2015 Standard Guide for Classifying and Specifying Adhesives

ASTM E 1 : 2014 : REDLINE Standard Specification for ASTM Liquid-in-Glass Thermometers
ASTM D 1016 : 2005 : EDT 1 Standard Test Method for Purity of Hydrocarbons from Freezing Points
ASTM E 2251 : 2014 : REDLINE Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM E 1137 : 1997 Standard Specification for Industrial Platinum Resistance Thermometers

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.