ASTM D 1922 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
05-25-2023
English
05-01-2015
CONTAINED IN VOL. 08.01, 2015 Describes the determination of the average force to propagate tearing through a specified length of plastic film or nonrigid sheeting after the tear has been started, using an Elmendorf-type tearing tester.
1.1This test method2 covers the determination of the average force to propagate tearing through a specified length of plastic film or nonrigid sheeting after the tear has been started, using an Elmendorf-type tearing tester. Two specimens are cited, a rectangular type, and one with a constant radius testing length. The latter shall be the preferred or referee specimen.
1.2Because of (1) difficulties in selecting uniformly identical specimens, (2) the varying degree of orientation in some plastic films, and (3) the difficulty found in testing highly extensible or highly oriented materials, or both, the reproducibility of the test results may be variable and, in some cases, not good or misleading. Provisions are made in the test method to address oblique directional tearing which may be found with some materials.
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 13.1.
Note 1:Film has been arbitrarily defined as sheeting having nominal thickness not greater than 0.25 mm (0.010 in.).
Note 2:This standard is equivalent to ISO 6383-2.
| Committee |
D 20
|
| DocumentType |
Redline
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM D 2673 : 2014 : REDLINE | Standard Specification for Oriented Polypropylene Film |
| ASTM D 5047 : 2017 : REDLINE | Standard Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 4649 : 2003 : R2016 | Standard Guide for Selection and Use of Stretch Wrap Films |
| MIL-DTL-32130 Base Document:2003 | UNDERWEAR, CHEMICAL PROTECTIVE, TWO PIECE (UNDERSHIRT AND DRAWERS) |
| ASTM D 4649 : 2003 : R2009 | Standard Guide for Selection and Use of Stretch Wrap Films |
| ANSI INCITS 121 : 1984 : R2006 | TWO-SIDED, UNFORMATTED, 8-INCH (200-MM), 48-TPI, DOUBLE-DENSITY, FLEXIBLE, DISK CARTRIDGE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS FOR 13 262 FTPR TWO-HEADED APPLICATION |
| ASTM D 5509 : 1996 | Standard Practice for Exposing Plastics to a Simulated Compost Environment (Withdrawn 2002) |
| CAN/CSA-ISO/TS 16775:17 | Packaging for terminally sterilized medical devices — Guidance on the application of ISO 11607-1 and ISO 11607-2 (Adopted ISO technical specification 16775:2014, first edition, 2014-05-15) |
| S.R. CEN ISO/TS 16775:2014 | PACKAGING FOR TERMINALLY STERILIZED MEDICAL DEVICES - GUIDANCE ON THE APPLICATION OF ISO 11607-1 AND ISO 11607-2 (ISO/TS 16775:2014) |
| ASTM A 674 : 2010 : R2014 | Standard Practice for Polyethylene Encasement for Ductile Iron Pipe for Water or Other Liquids |
| ASTM F 2097 : 2016 : REDLINE | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM D 2103 : 2015 : REDLINE | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 3020 : 1989 | Specification for Polyethylene and Ethylene Copolymer Plastic Sheeting for Pond, Canal and Reservoir Lining (Withdrawn 1996) |
| ASTM D 3105 : 2017 : REDLINE | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| CEN ISO/TS 16775:2014 | Packaging for terminally sterilized medical devices - Guidance on the application of ISO 11607-1 and ISO 11607-2 (ISO/TS 16775:2014) |
| MIL-PRF-32380 Base Document:2011 | BAGS - UNIT PACK BARRIER, CHEMICAL, BIOLOGICAL PROTECTIVE CLOTHING AND ACCESSORIES |
| PD CEN ISO/TS 16775:2014 | Packaging for terminally sterilized medical devices. Guidance on the application of ISO 11607-1 and ISO 11607-2 |
| L-P-523 Revision D:1979 | PLASTIC SHEET AND FILM, FEP-FLUOROCARBON, EXTRUDED |
| ANSI INCITS 162 : 1988 : R1999 | INFORMATION SYSTEMS - TWO-SIDED, HIGH-DENSITY, UNFORMATTED, 5.25-INCH (130-MM), 96-TPI (3,8 TPMM), FLEXIBLE DISK CARTRIDGE FOR 13 262 FTPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| MIL-A-50424 Base Document:1969 | ACETAL, SHEETING (FOR USE WITH AMMUNITION) |
| ANSI INCITS 126 : 1986 : R2002 | INFORMATION TECHNOLOGY - ONE- AND TWO-SIDED DOUBLE DENSITYUNFORMATTED 5.25 INCH (130 MM) 96 TRACKS PER INCH (3.8 TRACKS PER MM) FLEXIBLE DISK CARTRIDGE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS FOR 7958 BPR USE |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM D 4869 : 2005 : EDT 1 | Standard Specification for Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing |
| ANSI INCITS 126 : 1986 : R2017 | INFORMATION TECHNOLOGY - ONE- AND TWO-SIDED DOUBLE DENSITYUNFORMATTED 5.25 INCH (130 MM) 96 TRACKS PER INCH (3.8 TRACKS PER MM) FLEXIBLE DISK CARTRIDGE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS FOR 7958 BPR USE |
| ANSI INCITS 162 : 1988 : R2004 | INFORMATION SYSTEMS - TWO-SIDED, HIGH-DENSITY, UNFORMATTED, 5.25-INCH (130-MM), 96-TPI (3,8 TPMM), FLEXIBLE DISK CARTRIDGE FOR 13 262 FTPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| AWWA C105/A21.5 : 2010 | POLYETHYLENE ENCASEMENT FOR DUCTILE-IRON PIPE SYSTEMS |
| CGSB 156.1 : 1995 | PLASTIC GARBAGE BAGS |
| ASTM A 674 : 2010 | Standard Practice for Polyethylene Encasement for Ductile Iron Pipe for Water or Other Liquids |
| ASTM D 4649 : 2003 | Standard Guide for Selection and Use of Stretch Wrap Films |
| ASTM D 4869 : 2005 | Standard Specification for Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing |
| ANSI INCITS 125 : 1985 : R2006 | TWO-SIDED, DOUBLE-DENSITY, UNFORMATTED, 5.25 INCH (130-MM), 48-TPI (1,9-TPMM), FLEXIBLE DISK CARTRIDGE FOR 7958 BPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| L-P-375 Revision D:1994 | PLASTIC FILM, FLEXIBLE, VINYL CHLORIDE |
| L-C-1021 Revision C:1979 | COVER, MATTRESS, AND PILLOW (PLASTIC) |
| MIL-B-44433 Base Document:1991 | BAG, BARRIER, MULTI-LAYER FILM |
| MIL B 29597 : (1) | BAG, ODOR BARRIER, FLEXIBLE (FOR FOOD CONTAMINATED PLASTIC WASTE) |
| ASTM D 3420 : 2014 : REDLINE | Standard Test Method for Pendulum Impact Resistance of Plastic Film |
| L-B-1283 Revision A:1977 | BAG, SOILED CLOTHES (WATER SOLUBLE PLASTIC) |
| ANSI/AAMI/ISO TIR16775:2014 | PACKAGING FOR TERMINALLY STERILIZED MEDICAL DEVICES - GUIDANCE ON THE APPLICATION OF ISO 11607-1 AND ISO 11607-2 |
| ANSI INCITS 125 : 1985 : R2001 | TWO-SIDED, DOUBLE-DENSITY, UNFORMATTED, 5.25 INCH (130-MM), 48-TPI (1,9-TPMM), FLEXIBLE DISK CARTRIDGE FOR 7958 BPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| ASTM D 5525 : 1994 : REV A | Standard Practice for Exposing Plastics to a Simulated Active Landfill Environment (Withdrawn 2002) |
| ASTM D 1593 : 2013 : REDLINE | Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting |
| ASTM D 5512 : 1996 | Standard Practice for Exposing Plastics to a Simulated Compost Environment Using an Externally Heated Reactor (Withdrawn 2002) |
| ISO/TS 16775:2014 | Packaging for terminally sterilized medical devices Guidance on the application of ISO 11607-1 and ISO 11607-2 |
| UNI CEN ISO/TS 16775 : 2014 | PACKAGING FOR TERMINALLY STERILIZED MEDICAL DEVICES - GUIDANCE ON THE APPLICATION OF ISO 11607-1 AND ISO 11607-2 |
| DDD-L-20 Revision F:1990 | LABEL: FOR CLOTHING, EQUIPAGE, AND TENTAGE, (GENERAL USE) |
| ANSI INCITS 121 : 1984 : R2001 | TWO-SIDED, UNFORMATTED, 8-INCH (200-MM), 48-TPI, DOUBLE-DENSITY, FLEXIBLE, DISK CARTRIDGE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS FOR 13 262 FTPR TWO-HEADED APPLICATION |
| ASTM D 4635 : 2016 : REDLINE | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| MIL-P-44406 Base Document:1990 | POUCHES, PLASTIC FILM |
| ANSI IT9.2 : 1998 | IMAGING MEDIA - PHOTOGRAPHIC PROCESSED FILMS, PLATES AND PAPERS - FILING ENCLOSURES AND STORAGE CONTAINERS |
| ASTM D 7119 : 2007 | Standard Guide for Sampling Spray Polyurethane Foam and Coating in Roofing |
| ASTM D 689 : 2017 | Standard Test Method for Internal Tearing Resistance of Paper |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 1004 : 2013 : REDLINE | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ISO 6383-2:1983 | Plastics Film and sheeting Determination of tear resistance Part 2: Elmendorf method |
| ASTM D 6988 : 2013 : REDLINE | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.