ASTM D 333 : 2001 : R2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Guide for Clear and Pigmented Lacquers
Available format(s)
Hardcopy , PDF
Superseded date
06-22-2021
Language(s)
English
Published date
07-11-2013
CONTAINED IN VOL. 06.02, 2017 Describes procedures for testing lacquers and lacquer coatings.
1.1These test methods cover procedures for testing lacquers and lacquer coatings. The test methods included are listed in Table 1.
Note 1—In accordance with Terminology D16, a lacquer is defined as a coating composition that is based on synthetic thermoplastic filmforming material dissolved in organic solvent(s) and that dries primarily by solvent evaporation. Typical lacquers include those based on nitrocellulose, other cellulose derivatives, vinyl resins, acrylic resins, etc.
Note 2—Lacquers may be applied under such diverse conditions, to so many different surfaces, and their dried films may be subjected to so many kinds of wear and exposure that it is not possible to assure desired performance from a single selection of test methods and numerical results therefrom. Those skilled in lacquer technology may find partial assurance of obtaining desired qualities in various types of lacquers through careful selection of the methods covered herein and intelligent interpretation of results therefrom.
Note 3—It is intended ultimately to remove all experimental procedures from Test Methods D333 and to establish them as a guide to the selection of test methods for lacquer and perhaps to interpretation of results therefrom. Temporarily there remain in Test Methods D333 a few tests that are too short or otherwise presently unsuitable for establishment under separate ASTM designations.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
| Committee |
D 01
|
| DocumentType |
Guide
|
| Pages |
6
|
| ProductNote |
Reconfirmed 2013
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 2832 : 1992 : R2016 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
| ASTM D 365 : 2001 : R2017 | Standard Guide for Soluble Nitrocellulose Base Solutions |
| ASTM D 3023 : 1998 : R2017 | Standard Practice for Determination of Resistance of Factory-Applied Coatings on Wood Products to Stains and Reagents |
| ASTM D 1644 : 2001 | Standard Test Methods for Nonvolatile Content of Varnishes |
| ASTM D 1005 : 1995 : R2020 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 3170 : 1987 : R1996 : EDT 1 | Standard Test Method for Chipping Resistance of Coatings |
| ASTM D 3278 : 2020 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 870 : 2015 | Standard Practice for Testing Water Resistance of Coatings Using Water Immersion |
| ASTM D 1475 : 2013 | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 2199 : 2003 | Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers |
| ASTM D 1210 : 1996 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 1535 : 2007 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 2091 : 1996 | Standard Test Method for Print Resistance of Lacquers |
| ASTM D 1014 : 2009 | Standard Practice for Conducting Exterior Exposure Tests of Paints and Coatings on Metal Substrates (Withdrawn 2018) |
| ASTM D 1475 : 1998 : R2012 | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 1544 : 1998 | Standard Test Method for Color of Transparent Liquids (Gardner Color Scale) |
| ASTM D 1729 : 2016 : REDLINE | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 1400 : 2000 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base (Withdrawn 2006) |
| ASTM D 2244 : 2015 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 823 : 1995 | Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels |
| ASTM D 1308 : 2002 : R2013 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 1209 : 2000 | Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale) |
| ASTM D 1475 : 1985 | Standard Test Method for Density of Paint, Varnish, Lacquer, and Related Products |
| ASTM D 1535 : 2012 : REV A | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 2244 : 2011 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 3278 : 1996 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 2091 : 1996 : R2017 | Standard Test Method for Print Resistance of Lacquers |
| ASTM D 1735 : 1999 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 1729 : 2016 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 1644 : 2001 : R2006 | Standard Test Methods for Nonvolatile Content of Varnishes |
| ASTM D 2805 : 2011 : R2018 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 1200 : 2010 : R2018 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 609 : 2017 : REDLINE | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
| ASTM D 2244 : 2009 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 660 : 1993 | Standard Test Method for Evaluating Degree of Checking of Exterior Paints |
| ASTM D 2199 : 2003 : R2013 | Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers |
| ASTM D 2199 : 2003 : R2007 | Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers |
| ASTM D 2244 : 2002 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1535 : 2013 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 2091 : 1996 : R2011 | Standard Test Method for Print Resistance of Lacquers |
| ASTM D 2244 : 2015 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 2009 : REV B | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1186 : 1993 | Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base |
| ASTM D 1200 : 2010 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 1544 : 2004 : R2018 | Standard Test Method for Color of Transparent Liquids (Gardner Color Scale) |
| ASTM D 1475 : 1998 : R2003 | Standard Test Method for Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 2244 : 2002 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1474 : 1998 : R2002 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM D 1005 : 1995 : R2001 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 3170 : 2003 | Standard Test Method for Chipping Resistance of Coatings |
| ASTM D 1644 : 2001 : R2012 | Standard Test Methods for Nonvolatile Content of Varnishes |
| ASTM D 93 : 1990 : EDT 1 | Standard Test Methods for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 1535 : 1968 | Standard Method Of Specifying Color By The Munsell System |
| ASTM D 16 : 2016 : REDLINE | TERMINOLOGY FOR PAINT, RELATED COATINGS, MATERIALS, AND APPLICATIONS |
| ASTM D 2244 : 2015 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 445 : 1988 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity) |
| ASTM D 3278 : 1982 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Setaflash Closed-Cup Apparatus |
| ASTM D 1200 : 2010 : R2014 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 1210 : 2005 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 1400 : 1994 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base |
| ASTM D 1644 : 2001 : R2017 | Standard Test Methods for Nonvolatile Content of Varnishes |
| ASTM D 1735 : 2014 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 610 : 2008 | Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces |
| ASTM D 1729 : 1996 : R2009 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 1535 : 2008 : EDT 1 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 2244 : 2016 : REDLINE | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 661 : 1993 | Standard Test Method for Evaluating Degree of Cracking of Exterior Paints |
| ASTM D 1475 : 1960 : R1968 | Standard Method Of Test For Density Of Paint, Varnish, Lacquer, And Related Products |
| ASTM D 2244 : 2014 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 662 : 1993 | Standard Test Method for Evaluating Degree of Erosion of Exterior Paints |
| ASTM D 2805 : 1996 : REV A | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 1729 : 1996 : R2003 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 1210 : 2005 : R2014 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 1200 : 1970 | Standard Method Of Test For Viscosity Of Paints, Varnishes, And Lacquers By Ford Viscosity Cup |
| ASTM D 1535 : 2014 : R2018 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 1535 : 2014 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 1308 : 2002 : EDT 1 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 2244 : 2005 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1475 : 1998 : R2008 | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 445 : 2019 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 1005 : 1995 : R2013 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 1200 : 1994 : R2005 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 3170 : 2012 | Standard Test Method for Chipping Resistance of Coatings |
| ASTM D 1209 : 2005 : EDT 1 | Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale) |
| ASTM D 1210 : 2005 : R2010 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 1535 : 2008 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 1200 : 1994 : R1999 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 1308 : 1979 : R1981 : EDT 1 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 1735 : 2014 : REDLINE | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 1474 : 1998 : R2008 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM D 1735 : 2004 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 1535 : 1997 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 3170 : 2003 : R2007 | Standard Test Method for Chipping Resistance of Coatings |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
| ASTM D 1186 : 2001 | Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base (Withdrawn 2006) |
| ASTM D 3170 : 2001 | Standard Test Method for Chipping Resistance of Coatings |
| ASTM D 1535 : 1989 | Standard Test Method for Specifying Color by the Munsell System |
| ASTM D 2244 : 2007 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1735 : 2008 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 2620 : 1987 : R1995 : EDT 1 | Standard Test Method for Light Stability of Clear Coatings (Withdrawn 2001) |
| ASTM D 1544 : 2004 | Standard Test Method for Color of Transparent Liquids (Gardner Color Scale) |
| ASTM D 1308 : 1987 : R1998 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 1014 : 1995 | Standard Practice for Conducting Exterior Exposure Tests of Paints on Steel |
| ASTM D 93 : 2000 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 445 : 2001 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity) |
| ASTM D 1535 : 2000 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 1729 : 1996 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 445 : 2021 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 2805 : 2011 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 1211 : 1997 | Standard Test Method for Temperature-Change Resistance of Clear Nitrocellulose Lacquer Films Applied to Wood (Withdrawn 2006) |
| ASTM D 93 : 1985 | Standard Test Method for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 2204 : 1965 : R1970 | Method of Test for Perspiration Resistance of Organic Coatings (Withdrawn 1975) |
| ASTM D 1209 : 2005 : R2011 | Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale) |
| ASTM D 1544 : 2004 : R2010 | Standard Test Method for Color of Transparent Liquids (Gardner Color Scale) |
| ASTM D 1535 : 2012 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 1005 : 1995 : R2007 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 1014 : 2002 | Standard Practice for Conducting Exterior Exposure Tests of Paints and Coatings on Metal Substrates |
| ASTM D 1735 : 2002 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 56 : 1987 | Standard Test Method for Flash Point by Tag Closed Tester |
| ASTM D 1308 : 2002 : R2007 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 1474 : 1998 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM D 2244 : 2009 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 658 : 1991 | Standard Test Method for Abrasion Resistance of Organic Coatings by Air Blast Abrasive (Withdrawn 1996) |
| ASTM D 2244 : 1993 : R2000 | Standard Test Method for Calculation of Color Differences From Instrumentally Measured Color Coordinates |
| ASTM D 2090 : 1998 | Standard Test Method for Clarity and Cleanness of Paint and Ink Liquids (Withdrawn 2007) |
| ASTM D 1209 : 2005 | Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale) |
| ASTM D 1535 : 2006 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 1475 : 2013 : REDLINE | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 522 : 1993 : REV A | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
| ASTM D 2199 : 1982 : R1999 | Standard Test Method for Measurement of Plasticizer Migration From Vinyl Fabrics to Lacquers |
| ASTM D 1535 : 2001 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 1475 : 1998 | Standard Test Method for Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 659 : 1986 : EDT 1 | Method of Evaluating Degree of Chalking of Exterior Paints |
| ASTM D 3278 : 1996 : R2004 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 2805 : 1996 : REV A : R2003 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 93 : 1997 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 1005 : 1995 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 1308 : 2002 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 3278 : 1996 : R2011 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus (Withdrawn 2020) |
| ASTM D 2091 : 1996 : R2003 | Standard Test Method for Print Resistance of Lacquers |
| ASTM D 1209 : 2005 : R2019 | Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale) |
US$75.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.