ASTM D 4565 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Methods for Physical and Environmental Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable
11-13-2020
English
04-01-2015
CONTAINED IN VOL. 10.02, 2017 Defines procedures for physical testing of thermoplastic jackets and insulations on telecommunications wire and cable and testing of physical characteristics and environmental performance properties of completed products.
1.1These test methods cover procedures for the physical testing of thermoplastic insulations and jackets used on telecommunications wire and cable and the testing of physical characteristics and environmental performance properties of completed products. To determine the procedure to be used on the particular insulation or jacket or on the completed wire or cable, make reference to the specification for that product.
1.2The test methods appear in the following sections of this standard:
| Procedure | Sections |
| Dimensional measurements of insulations, jackets, | |
| Cross-sectional areas | 9 |
| Diameters | 6 |
| Eccentricity | 8 |
| Thickness | 7 |
| Physical and environmental tests of insulation and jackets | 10 – 25 |
| Aging test (jackets only) | 24 |
| Cold bend (insulation only) | 16 |
| Environmental stress crack (polyolefin jackets only) | 21 |
| Heat distortion (jackets only) | 22 |
| Heat shock (jackets only) | 23 |
| Insulation adhesion | 19 |
| Insulation and jacket shrinkback (oven test) | 14 |
| Insulation compression | 20 |
| Insulation shrinkback (solder test) | 15 |
| Melt flow rate change—polyolefin materials | 12 |
| Oil immersion test (jackets only) | 25 |
| Oxygen induction time (polyolefin insulation only) | 17 |
| Oxygen induction time (cable filling compound only) | 18 |
| Tensile and elongation tests | 13 |
| Physical and environmental tests of insulations and jackets of completed wire and cable | |
| Cable Torsion Test | 38 |
| Compound flow test (filled core wire and cable only) | 42 |
| Corrugation extensibility test | 36 |
| Cable impact test | 33 |
| Jacket bonding tests | 29 |
| Procedure | Sections |
| Jacket notch test | 32 |
| Jacket peel or pull | 28 |
| Jacket slip strength test | 30 |
| Pressure test (air core wire and cable only) | 40 |
| Sheath adherance test | 31 |
| Water penetration test (filled core wire and cable only) | 41 |
| Wire and cable bending test | 34 |
| Wire breaking strength | 37 |
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard, except where only SI units are given.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific caution statement see 19.1.
| Committee |
D 09
|
| DocumentType |
Redline
|
| Pages |
24
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| GR 1398 CORE : ISSUE 1 REV 1 | GENERIC REQUIREMENTS FOR COAXIAL DROP CABLE |
| CEI EN 50290-2-25 : 2014 | COMMUNICATION CABLES - PART 2-25: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION COMPOUNDS |
| TIA 455-82 : B1992 | FLUID PENETRATION TEST FOR FLUID-BLOCKED FIBER OPTIC CABLE |
| TIA/EIA 455-81 : B2000 | FOTP-81 - COMPOUND FLOW (DRIP) TEST FOR FILLED FIBER OPTIC CABLE |
| ASTM E 1858 : 2008 : R2015 : EDT 1 | Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry |
| EN 62680-2-3:2015 | Universal Serial Bus interfaces for data and power - Part 2-3: Universal Serial Bus Cables and Connectors Class Document, Revision 2.0 (TA 14) |
| EN 50290-2-25:2013 | COMMUNICATION CABLES - PART 2-25: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION COMPOUNDS |
| ASTM D 5885 : 2006 : R2012 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| ASTM E 1858 : 2008 | Standard Test Method for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry |
| UNE-EN 50290-2-25:2014 | Communication cables - Part 2-25: Common design rules and construction - Polypropylene insulation compounds |
| ASTM E 2046 : 2014 : REDLINE | Standard Test Method for Reaction Induction Time by Thermal Analysis |
| CSA T568.2 : 2005 | COMMERCIAL BUILDING TELECOMMUNICATIONS CABLING STANDARD - PART 2: BALANCED TWISTED-PAIR CABLING COMPONENTS |
| SCTE 177 : 2012 | SPECIFICATION FOR BRAIDED 75 OHMS, MINI-SERIES QUAD SHIELD COAXIAL CABLE FOR CMTS AND SDI CABLES |
| GR 2949 CORE : ISSUE 1 | GENERIC REQUIREMENTS FOR BURIED HYBRID COAXIAL/TWISTED PAIR CABLE |
| ASTM D 4731 : 2013 : REDLINE | Standard Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable |
| ASTM E 2009 : 2008 | Standard Test Method for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry |
| IEC 62680-4:2013 | Universal serial bus interfaces for data and power - Part 4: Universal Serial Bus Cables and Connectors Class Document, Revision 2.0 |
| 13/30281390 DC : 0 | BS EN 50290-2-25 - COMMUNICATION CABLES - PART 2-25: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION COMPOUNDS |
| SCTE 71 : 2008 | SPECIFICATION FOR BRAIDED, 75 OHM, COAXIAL, MULTI-PURPOSE CABLE |
| ASTM D 5885 : 2006 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| BS EN 50290-2-25:2013 | Communication cables Common design rules and construction. Polypropylene insulation compounds |
| 13/30293736 DC : 0 | BS EN 50290-2-33 - COMMUNICATION CABLES - PART 2-33: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR MULTI ELEMENT METALLIC DATA CABLES FOR INDOOR APPLICATION |
| ASTM D 4730 : 2013 : REDLINE | Standard Specification for Flooding Compounds for Telecommunications Wire and Cable |
| PREN 50290-2-38 : DRAFT 2013 | COMMUNICATION CABLES - PART 2-38: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR COAXIAL CABLES |
| ICEA S 89 648 : 2011 | AERIAL SERVICE WIRE TECHNICAL REQUIREMENTS |
| ASTM D 5885/D5885M : 2017 : REDLINE | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| ASTM E 2009 : 2008 : R2014 : EDT 1 | Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM D 4732 : 2013 : REDLINE | Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable |
| IEC 62680-2-3:2015 | Universal serial bus interfaces for data and power - Part 2-3: Universal Serial Bus Cables and Connectors Class Document Revision 2.0 |
| NF EN 50290-2-25 : 2017 | COMMUNICATION CABLES - PART 2-25: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION COMPOUNDS |
| SCTE 74 : 2011 | SPECIFICATION FOR BRAIDED 75 OHM FLEXIBLE RF COAXIAL DROP CABLE |
| PREN 50290-2-33 : DRAFT 2013 | COMMUNICATION CABLES - PART 2-33: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR MULTI ELEMENT METALLIC DATA CABLES FOR INDOOR APPLICATION |
| 13/30293741 DC : 0 | BS EN 50290-2-37 - COMMUNICATION CABLES - PART 2-37: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR COAXIAL CABLES |
| SCTE 100 : 2010 | SPECIFICATION FOR 75 OHM SMOOTH ALUMINUM SUBSCRIBER ACCESS CABLE |
| CSA T568.2 : 2005 : R2010 | COMMERCIAL BUILDING TELECOMMUNICATIONS CABLING STANDARD - PART 2: BALANCED TWISTED-PAIR CABLING COMPONENTS |
| SCTE 15 : 2016 | SPECIFICATION FOR TRUNK, FEEDER AND DISTRIBUTION COAXIAL CABLE |
| PREN 50290-2-37 : DRAFT 2013 | COMMUNICATION CABLES - PART 2-37: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR COAXIAL CABLES |
| I.S. EN 50290-2-25:2013 | COMMUNICATION CABLES - PART 2-25: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION COMPOUNDS |
| BS EN 62680-4:2014 | Universal serial bus interfaces for data and power Universal Serial Bus Cables and Connectors Class Document, Revision 2.0 |
| BS EN 62680-2-3:2015 | Universal Serial Bus interfaces for data and power Universal Serial Bus Cables and Connectors Class Document Revision 2.0 (TA 14) |
| EN 62680-4:2014 | Universal serial bus interfaces for data and power - Part 4: Universal Serial Bus Cables and Connectors Class Document, Revision 2.0 |
| 13/30293745 DC : 0 | BS EN 50290-2-38 - COMMUNICATION CABLES - PART 2-38: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR COAXIAL CABLES |
| SCTE 117 : 2010 | SPECIFICATION FOR BRAIDED 75 OHMS, MINI-SERIES BROADBAND COAXIAL CABLE |
| SCTE 244 : 2018 | SPECIFICATION FOR BRAIDED 75 OHMS, MICRO-SERIES QUAD SHIELD COAXIAL CABLE FOR CONNECTIVITY AND DENSE CCAP/EDGE QAM APPLICATIONS |
| PREN 50290-2-25 : DRAFT 2013 | COMMUNICATION CABLES - PART 2-25: COMMON DESIGN RULES AND CONSTRUCTION - POLYPROPYLENE INSULATION COMPOUNDS |
| ASTM D 1248 : 2016 : REDLINE | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 4731 : 2013 : REDLINE | Standard Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable |
| ASTM D 3032 : 2016 : REDLINE | Standard Test Methods for Hookup Wire Insulation |
| ASTM D 1238 : 2013 : REDLINE | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 4732 : 2013 : REDLINE | Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable |
| ASTM D 2633 : 2013-03 | TEST METHODS FOR THERMOPLASTIC INSULATIONS AND JACKETS FOR WIRE AND CABLE |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1693 : 2015 : REDLINE | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.