• There are no items in your cart

ASTM D 6265 : 2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Separation of Contaminants in Polymers Using an Extruder Filter Test
Available format(s)

Hardcopy , PDF

Superseded date

03-20-2023

Language(s)

English

Published date

01-16-2018

1.1This practice covers a means to separate the unmolten particles, gels, and impurities contaminating a polymer sample. The procedure may be used to remove gels and incompatible materials that may cause imperfections in the final extruded product. Under pressure, most gels will break up or deform and pass through a wire mesh filter, however high molecular weight gels may not break up or deform.

1.2Materials isolated on a wire mesh filter can be identified by spectroscopic or other analytical means.

Note 1:Although not presented as a quantitative method, the procedure presented in this practice may be used to provide quantitative results at the discretion of the user. The user assumes the responsibility to verify the reproducibility of quantitative results. Detection limit depends on the mesh size of the filter screen, but the procedure is generally applicable to the separation of immiscible contaminants present at concentrations greater than 0.1 %.

1.3The values stated in SI units are to be regarded as standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see Section 8

Note 2:There is no known ISO equivalent to this standard.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 20
DocumentType
Standard Practice
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1238 : 2000 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 1238 : 2004 : REV C Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 1238 : 2023 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 1238 : 2013 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 1238 : 2010 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1238 : 2004 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 1238 : 2001 : EDT 1 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 1238 : 2020 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 1238 : 2004 : REV A Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 1238 : 1985 Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.