ASTM D 6783 : 2005 : REV A : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
07-25-2022
English
01-26-2018
CONTAINED IN VOL. 08.03, 2018 Describes polymer concrete pipe, 6 in. (150 mm) through 144 in. (3660 mm), intended for use in gravity-flow systems for conveying sanitary sewage, storm water, and industrial wastes.
1.1This specification covers polymer concrete pipe, 6 in. (150 mm) through 144 in. (3 660 mm), intended for use in gravity-flow systems for conveying sanitary sewage, storm water, and industrial wastes.
1.2Although this specification is suited primarily for pipe to be installed by direct burial and pipe jacking, it may be used to the extent applicable for other installations such as sliplining and rehabilitation of existing pipelines.
Note 1:Unlike reinforced thermosetting resin pipes, polymer concrete pipe is designed and installed using rigid pipe design theory and practices.
1.3The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2:There is no known ISO equivalent to this standard.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4161 : 1996 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals |
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 4161 : 2001 : R2005 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals |
| ASTM D 4161 : 2001 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals |
| ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 2584 : 2002 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 477 : 2014 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 3681 : 2006 | Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
| ASTM D 3859 : 2015 : REDLINE | Standard Test Methods for Selenium in Water |
| ASTM F 477 : 2002 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM D 2584 : 2008 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 2584 : 1994 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D 3567 : 1997 : R2006 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3681 : 2001 : EDT 1 | Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM F 477 : 2014 : REDLINE | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM D 3681 : 2018 | Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3567 : 2017 : R2022 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 2584 : 2011 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM F 477 : 2014 : R2021 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM D 4161 : 2014 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals |
| ASTM D 3567 : 1997 : R2002 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 3681 : 2012 : EDT 1 | Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
| ASTM C 136 : 2006 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
| ASTM D 2584 : 1968 | Standard Method Of Test For Ignition Loss Of Cured Reinforced Resins |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 3681 : 2001 | Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
| ASTM D 3681 : 1996 | Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
| ASTM D 648 : 2016 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 3567 : 1997 | Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 2584 : 2018 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM C 117 : 2017 : REDLINE | Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing |
| ASTM D 3681 : 2012 | Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
| ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4161 : 2014 : R2019 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals |
| ASTM D 4161 : 2001 : R2010 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals |
| ASTM C 33 : 1985 | Standard Specification for Concrete Aggregates |
| ASTM C 136 : 1996 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
| ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 3567 : 2017 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 3567 : 1997 : R2011 | Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings |
| ASTM D 3892 : 2015 : REDLINE | PRACTICE FOR PACKAGING/PACKING OF PLASTICS |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.