• There are no items in your cart

ASTM D 7359 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Total Fluorine, Chlorine and Sulfur in Aromatic Hydrocarbons and Their Mixtures by Oxidative Pyrohydrolytic Combustion followed by Ion Chromatography Detection (Combustion Ion Chromatography-CIC)
Available format(s)

Hardcopy , PDF

Superseded date

04-27-2023

Language(s)

English

Published date

12-17-2018

This test method covers the individual determination of total fluorine, chlorine and sulfur in aromatic hydrocarbons and their mixtures. Samples containing 0.10 to 10 mg/kg of each element can be analyzed.

1.1This test method covers the individual determination of total fluorine, chlorine and sulfur in aromatic hydrocarbons and their mixtures. Samples containing 0.10 to 10 mg/kg of each element can be analyzed.

1.2This method can be applied to sample concentrations outside the range of the scope by dilution of the sample in an appropriate solvent to bring the total concentrations of fluorine, chlorine and sulfur within the range covered by the test method. However, it is the responsibility of the analyst to verify the solubility of the sample in the solvent and that the diluted sample results conform to the precision and accuracy of the method.

1.2.1Special considerations must be made in order to attain detection limits below 1.0 mg/kg in a sample. The instrument must be clean and properly maintained to address potential sources of contamination, or carryover, or both. Multiple sequential injections shall be completed until a stable background is attained. A stable background is considered to be achieved when the analysis of a minimum of three consecutive system blanks have area counts equal to or less than 5 % RSD for the anions of interest.

1.3In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 9.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 16
DocumentType
Test Method
Pages
9
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4077 : 2017 Standard Specification for Cumene (Isopropylbenzene)
ASTM D 3193 : 2019 Standard Specification for Ethylbenzene
ASTM D 2359 : 2018 : REV A Standard Specification for Refined Benzene-535
ASTM D 8149 : 2017 Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants
ASTM D 7566 : 2019 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
ASTM D 7124 : 2017 Standard Specification for Benzene for Use with Zeolite Based Catalysts
ASTM D 7125 : 2017 Standard Specification for Cumene (Isopropylbenzene) Manufactured Via a Zeolite Process
ASTM D 7185 : 2017 Standard Specification for Low Toluene Low Dioxane (LTLD) Benzene
ASTM D 4054 : 2019 Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
ASTM D 5211 : 2017 Standard Specification for Xylenes for <emph type="ital">p</emph>-Xylene Feedstock
ANSI/NEMA 62321-3-2:2020 Determination of certain substances in electrotechnical products - Part 3-2: Screening - Fluorine, bromine and chlorine in polymer and electronics by combustion-ion chromatography (C-IC)
ASTM D 2359 : 2019 Standard Specification for Refined Benzene-535
ASTM D 8149 : 2020 Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants
ASTM D 7185 : 2019 Standard Specification for Low Toluene Low Dioxane (LTLD) Benzene
ASTM D 7124 : 2019 Standard Specification for Benzene for Use with Zeolite Based Catalysts
ASTM D 4077 : 2022 Standard Specification for Cumene (Isopropylbenzene)
ASTM D 7566 : 2022 : REV A Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
ASTM D 4054 : 2022 Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
ASTM D 5211 : 2019 Standard Specification for Xylenes for <emph type="ital">p</emph>-Xylene Feedstock

ASTM D 6809 : 2002 : R2016 Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials
ASTM D 6809 : 2020 Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials
ASTM E 177 : 1990 : REV A : R1996 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM E 29 : 2013 : R2019 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 3437 : 1999 Standard Practice for Sampling and Handling Liquid Cyclic Products
ASTM D 3505 : 1996 Standard Test Method for Density or Relative Density of Pure Liquid Chemicals
ASTM E 29 : 2002 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 1193 : 1977 : R1983 : EDT 1 Standard Specification for Reagent Water
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 3437 : 2010 Standard Practice for Sampling and Handling Liquid Cyclic Products
ASTM D 3505 : 2012 Standard Test Method for Density or Relative Density of Pure Liquid Chemicals
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2023 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 1193 : 2006 : R2011 Standard Specification for Reagent Water
ASTM E 288 : 1994 : R1998 Standard Specification for Laboratory Glass Volumetric Flasks
ASTM D 3505 : 1996 : R2006 Standard Test Method for Density or Relative Density of Pure Liquid Chemicals
ASTM D 3437 : 2015 : R2022 Standard Practice for Sampling and Handling Liquid Cyclic Products
ASTM D 6809 : 2002 : R2012 Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials
ASTM D 3505 : 2018 Standard Test Method for Density or Relative Density of Pure Liquid Chemicals (Withdrawn 2023)
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 1193 : 1991 Standard Specification for Reagent Water
ASTM D 3437 : 2011 Standard Practice for Sampling and Handling Liquid Cyclic Products
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 3437 : 2008 Standard Practice for Sampling and Handling Liquid Cyclic Products
ASTM D 3437 : 2003 Standard Practice for Sampling and Handling Liquid Cyclic Products
ASTM D 3437 : 2015 Standard Practice for Sampling and Handling Liquid Cyclic Products
ASTM D 6809 : 2002 Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials
ASTM D 1193 : 1970 Standard Specification For Reagent Water
ASTM D 1193 : 2006 Standard Specification for Reagent Water
ASTM D 1193 : 1999 Standard Specification for Reagent Water
ASTM D 6809 : 2002 : R2007 Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials
ASTM D 1193 : 2006 : R2018 Standard Specification for Reagent Water
ASTM D 3505 : 1996 : R2000 Standard Test Method for Density or Relative Density of Pure Liquid Chemicals
ASTM D 3505 : 2012 : EDT 1 Standard Test Method for Density or Relative Density of Pure Liquid Chemicals
ASTM E 29 : 2022 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.