Standard Guide for Qualification Testing of Coatings Used in Coating Service Level I in Nuclear Power Plants

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

03-01-2019

Publisher

American Society for Testing and Materials

This guide provides an approach to identifying the need for and development of a test document to qualify coatings for Coating Service Level I (CSLI) service in nuclear power plants.

1.1This guide provides an approach to identifying the need for and development of a test document to qualify coatings for Coating Service Level I (CSLI) service in nuclear power plants.

1.2It is the intent of this guide to provide a recommended basis for establishing a coatings qualification test document, not to mandate a singular basis for all test documents. Variations or simplifications of the process described in this guide may be appropriate for any given operating or new construction nuclear power plant depending on its licensing commitments.

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 33
DocumentType	Guide
Pages	4
ProductNote	THIS STANDARD ALSO REFERS TO- ASTM C177 - 19, ASTM D7108 - 12(2018), ASTM E1269 - 11(2018), ASTM E1530 - 19
PublisherName	American Society for Testing and Materials
Status	Current

ASTM D 5139 : 1990 : R2001	Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants (Withdrawn 2010)
ASTM E 1269 : 2001	Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 5163 : 2005 : REV A	Standard Guide for Establishing Procedures to Monitor the Performance of Service Level I Coatings in an Operating Nuclear Power Plant
ASTM E 84 : 2023 : REV D	Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM D 5144 : 2008 : R2016	Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants
ASTM C 177 : 2019	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
ASTM E 1530 : 1999	Standard Test Method for Evaluating the Resistance to Thermal Transmission of Thin Specimens of Materials by the Guarded Heat Flow Meter Technique
ASTM D 4541 : 2009	Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 84 : 2023 : REV C	Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM D 4538 : 2005 : EDT 1	Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
ASTM E 1461 : 2011	Standard Test Method for Thermal Diffusivity by the Flash Method
ASTM E 1461 : 2007	Standard Test Method for Thermal Diffusivity by the Flash Method
ASTM D 5139 : 2012	Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants
ASTM D 4538 : 2005	Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
ASTM E 1269 : 2005	Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 3912 : 2010	Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants
ASTM D 7108 : 2012	Standard Guide for Establishing Qualifications for a Nuclear Coatings Specialist
ASTM D 5144 : 2008 : EDT 1	Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants
ASTM D 5163 : 2016 : R2021	Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants
ASTM E 84 : 2023	Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM D 4060 : 2007	Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM D 4538 : 2015	Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
ASTM D 4541 : 2009 : EDT 1	Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 3911 : 1995	Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions
ASTM E 1530 : 2019	Standard Test Method for Evaluating the Resistance to Thermal Transmission by the Guarded Heat Flow Meter Technique
ASTM D 5163 : 2008	Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants
ASTM D 4082 : 1995	Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants
ASTM D 7108 : 2005	Standard Guide for Establishing Qualifications for a Nuclear Coatings Specialist
ASTM E 1269 : 1999	Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM E 84 : 2021	Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM D 5139 : 2019	Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants
ASTM D 3911 : 2016 : R2021	Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions
ASTM D 4082 : 1989	Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants
ASTM E 84 : 2022	Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM D 8104 : 2017 : R2023	Standard Guide for Determining Coating Qualification Test Data Applicability
ASTM D 5139 : 2010	Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants
ASTM D 4541 : 2002	Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 1530 : 2011	Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
ASTM D 5163 : 2016	Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants
ASTM E 1530 : 2004	Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
ASTM D 4060 : 2001	Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM D 4082 : 2002	Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants
ASTM E 84 : 2020	Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM E 1530 : 2006	Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
ASTM E 84 : 2021 : REV A	Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM D 5163 : 2004	Standard Guide for Establishing Procedures to Monitor the Performance of Service Level I Coatings in an Operating Nuclear Power Plant
ASTM D 4541 : 2017	Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 4541 : 2022	Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 648 : 2019 : REV A : EDT 1	Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source
ASTM D 5144 : 2000	Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants
ASTM E 1461 : 1992	Standard Test Method for Thermal Diffusivity of Solids by the Flash Method
ASTM D 5163 : 1991 : R1996	Standard Guide for Establishing Procedures to Monitor the Performance of Safety Related Coatings in an Operating Nuclear Power Plant
ASTM E 1530 : 2011 : R2016	Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
ASTM D 4082 : 2010 : R2017	Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants
ASTM D 4082 : 2010 : R2023	Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants
ASTM D 5139 : 1990 : R1996	Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants
ASTM E 1269 : 2004	Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 3912 : 1995	Standard Test Method for Chemical Resistance of Coatings Used in Light-Water Nuclear Power Plants
ASTM D 5163 : 2004 : REV A	Standard Guide for Establishing Procedures to Monitor the Performance of Service Level I Coatings in an Operating Nuclear Power Plant
ASTM D 4538 : 2021	Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
ASTM D 4538 : 2013	Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
ASTM E 84 : 2023 : REV B	Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM D 7108 : 2012 : R2018	Standard Guide for Establishing Qualifications for a Nuclear Coatings Specialist
ASTM C 177 : 2019 : EDT 1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
ASTM D 3912 : 2010 : R2023	Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants
ASTM E 1269 : 2011	Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 4060 : 1995	Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM D 5144 : 2008	Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants
ASTM E 1461 : 2013 : R2022	Standard Test Method for Thermal Diffusivity by the Flash Method
ASTM E 1461 : 2013	Standard Test Method for Thermal Diffusivity by the Flash Method
ASTM E 1461 : 2001	Standard Test Method for Thermal Diffusivity of Solids by the Flash Method
ASTM D 3912 : 1980 : R1989	Standard Test Method for Chemical Resistance of Coatings Used in Light-Water Nuclear Power Plants
ASTM E 84 : 2023 : REV A	Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM D 8104 : 2017	Standard Guide for Determining Coating Qualification Test Data Applicability
ASTM D 4538 : 1995	Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
ASTM D 3911 : 2016	Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions
ASTM D 4541 : 1995 : EDT 1	Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 1269 : 2011 : R2018	Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 5144 : 2008 : R2021	Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants
ASTM D 4060 : 2014	Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM D 4082 : 2010	Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants
ASTM D 5163 : 2005	Standard Guide for Establishing Procedures to Monitor the Performance of Service Level I Coatings in an Operating Nuclear Power Plant
ASTM D 3912 : 2010 : R2017	Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants
ASTM D 4060 : 2010	Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM D 3911 : 2008	Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions
ASTM D 3911 : 2003	Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions
ASTM D 4060 : 2019	Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM E 648 : 2023	Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source