• There are no items in your cart

ASTM D 857 : 2017 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Test Method for Aluminum in Water
Available format(s)

PDF

Language(s)

English

Published date

06-01-2017

CONTAINED IN VOL. 11.01, 2017 Specifies the direct flame atomic absorption determination of aluminum in the nitrous oxide-acetylene flame.

1.1This test method covers the direct flame atomic absorption determination of aluminum in the nitrous oxide-acetylene flame.

1.2This test method is applicable to waters containing dissolved and total recoverable aluminum in the range from 0.5 to 5.0 mg/L. Aluminum concentrations as high as approximately 50 mg/L can be determined using this test method without dilution. However, no precision and bias data are available for concentrations greater than 5.0 mg/L.

1.3This test method was tested on reagent, natural, and potable waters. It is the user's responsibility to ensure the validity of this test method for waters of untested matrices.

1.4The same digestion procedure may be used to determine total recoverable nickel (Test Methods D1886), chromium (Test Methods D1687), cobalt (Test Methods D3558), copper (Test Methods D1688), iron (Test Methods D1068), lead (Test Methods D3559), manganese (Test Methods D858), and zinc (Test Methods D1691).

1.5Precision and bias data have been obtained on reagent, natural, and potable waters. It is the responsibility of the user to ensure the validity of this test method on untested matrices.

1.6The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversion to inch-pound units that are provided for information only and are not considered standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 7.5, 8.4, and Note 2.

1.8Former Test Methods A (Fluorometric) and B and C (Spectrophotometric) were discontinued. Refer to Appendix X1 for historical information.

1.9This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 19
DocumentType
Redline
Pages
8
PublisherName
American Society for Testing and Materials
Status
Current

Standards Relationship
SANS 381 : 2ED 2017 Identical

ASTM D 3089 : 1997 : R2008 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
API 45 : 1998 : R2012 RECOMMENDED PRACTICE FOR ANALYSIS OF OILFIELD WATERS
ASTM D 1971 : 2016 : REDLINE Standard Practices for Digestion of Water Samples for Determination of Metals by Flame Atomic Absorption, Graphite Furnace Atomic Absorption, Plasma Emission Spectroscopy, or Plasma Mass Spectrometry
ASTM D 5091 : 1995 : R2001 Standard Guide for Water Analysis for Electrodialysis/Electrodialysis Reversal Applications
ASTM D 4195 : 2008 Standard Guide for Water Analysis for Reverse Osmosis and Nanofiltration Application
ASTM D 4195 : 2008 : R2014 Standard Guide for Water Analysis for Reverse Osmosis and Nanofiltration Application (Withdrawn 2023)
ASTM D 5091 : 1995 Standard Guide for Water Analysis for Electrodialysis/Electrodialysis Reversal Applications
ASTM D 5091 : 1995 : R2014 Standard Guide for Water Analysis for Electrodialysis/Electrodialysis Reversal Applications (Withdrawn 2023)
ASME PV CODE 7 : 2017 BPVC Section VII-BOILER AND PRESSURE VESSEL CODE - RECOMMENDED GUIDELINES FOR THE CARE OF POWER BOILERS
ASTM D 5091 : 1995 : R2007 Standard Guide for Water Analysis for Electrodialysis/Electrodialysis Reversal Applications
SAE J 1726 : 2015 CHARGE AIR COOLER INTERNAL CLEANLINESS, LEAKAGE, AND NOMENCLATURE
API 45:1998 RECOMMENDED PRACTICE FOR ANALYSIS OF OILFIELD WATERS
ASME PTC31 : 2011 PERFORMANCE TEST CODES - HIGH-PURITY WATER TREATMENT SYSTEMS
ASME PTC31 : 2011 : R2017 PERFORMANCE TEST CODES - HIGH-PURITY WATER TREATMENT SYSTEMS

ASTM D 1129 : 2013 : REDLINE Standard Terminology Relating to Water
ASTM D 2777 : 2013 : REDLINE Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water
ASTM D 858 : 2017 : REDLINE Standard Test Methods for Manganese in Water
ASTM D 1687 : 2017 : REDLINE Standard Test Methods for Chromium in Water
ASTM D 1068 : 2015 : REDLINE Standard Test Methods for Iron in Water
ASTM D 3591 : 2017 : REDLINE Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds
ASTM D 1691 : 2017 : REDLINE Standard Test Methods for Zinc in Water
ASTM D 5673 : 2016 : REDLINE Standard Test Method for Elements in Water by Inductively Coupled Plasma—Mass Spectrometry
ASTM D 1886 : 2014 : REDLINE Standard Test Methods for Nickel in Water
ASTM D 1688 : 2017 : REDLINE Standard Test Methods for Copper in Water
ASTM D 3558 : 2015 : REDLINE Standard Test Methods for Cobalt in Water

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.