• There are no items in your cart

ASTM E 1004 : 2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method
Available format(s)

Hardcopy , PDF

Superseded date

02-09-2024

Language(s)

English

Published date

07-06-2017

1.1This test method covers a procedure for determining the electrical conductivity of nonmagnetic metals using the electromagnetic (eddy current) method. The procedure has been written primarily for use with commercially available direct reading electrical conductivity instruments. General purpose eddy current instruments may also be used for electrical conductivity measurements but will not be addressed in this test method.

1.2This test method is applicable to metals that have either a flat or slightly curved surface and includes metals with or without a thin nonconductive coating.

1.3Eddy current determinations of electrical conductivity may be used in the sorting of metals with respect to variables such as type of alloy, aging, cold deformation, heat treatment, effects associated with non-uniform heating or overheating, and effects of corrosion. The usefulness of the examinations of these properties is dependent on the amount of electrical conductivity change caused by a change in the specific variable.

1.4Electrical conductivity, when evaluated with eddy current instruments, is usually expressed as a percentage of the conductivity of the International Annealed Copper Standard (% IACS) or Siemens/meter (S/m). The conductivity of the Annealed Copper Standard is defined to be 0.58  × 108 S/m (100 % IACS) at 20°C.

1.5The values stated in SI units are regarded as standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 07
DocumentType
Test Method
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM B 700 : 2008 : R2014 Standard Specification for Electrodeposited Coatings of Silver for Engineering Use
ASTM E 543 : 2015 Standard Specification for Agencies Performing Nondestructive Testing
ASTM B 236 : 2007 : R2015 Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars)
SAE AMS4374A:2022 Aluminum Alloy, Extruded Profiles 8.9Zn - 2.2Cu - 2.2Mg - 0.15Zr (7136-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged
NFPA 1900:2024 Standard for Aircraft Rescue and Fireghting Vehicles, Automotive Fire Apparatus, Wildland Fire Apparatus, and Automotive Ambulances
NFPA 1910:2024 Standard for the Inspection, Maintenance, Refurbishment, Testing, and Retirement of In-Service Emergency Vehicles and Marine Firefighting Vessels
ASTM B 187/B187M : 2019 Standard Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes
MIL-HDBK-6870 Revision C:2020 NONDESTRUCTIVE INSPECTION PROGRAM REQUIREMENTS FOR AIRCRAFT AND MISSILE MATERIALS AND PARTS
ASTM B 937 : 2018 Standard Specification for Copper-Beryllium Seamless Tube (UNS Nos. C17500 and C17510)
ASTM B 441 : 2016 Standard Specification for Copper-Cobalt-Beryllium, Copper-Nickel-Beryllium, and Copper-Nickel-Lead-Beryllium Rod and Bar (UNS Nos. C17500, C17510, and C17465)
ASTM B 236M : 2007 : R2015 Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) (Metric) (Withdrawn 2024)
ASTM B 209M : 2014 Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric) (Withdrawn 2021)
ASTM B 870 : 2008 : R2014 Standard Specification for Copper-Beryllium Alloy Forgings and Extrusions Alloys (UNS Nos. C17500 and C17510)
ASTM B 241/B241M : 2016 Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube
ASTM B 316/B316M : 2015 Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods
ASTM B 221 : 2014 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
ASTM B 944 : 2011 : R2016 Standard Specification for Copper-Beryllium Welded Heat Exchanger and Condenser Tube (UNS No. C17510)
ASTM E 2338 : 2017 Standard Practice for Characterization of Coatings Using Conformable Eddy Current Sensors without Coating Reference Standards
ASTM B 209 : 2014 Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
ASTM B 317/B317M : 2007 : R2015 : EDT 1 Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor)
ASTM B 247 : 2015 Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings
ASTM B 247M : 2015 Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric)
ASTM B 210/B210M : 2019 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
ASTM B 211/B211M : 2019 Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
ASTM B 221M : 2013 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)
ASTM B 247 : 2020 Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings
ASTM B 316/B316M : 2020 Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods
ASTM B 187/B187M : 2020 Standard Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes
ASTM B 317/B317M : 2023 Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor)
ASTM B 700 : 2020 Standard Specification for Electrodeposited Coatings of Silver for Engineering Use
ASTM B 248M : 2022 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)
ASTM B 241/B241M : 2022 Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube
ASTM B 944 : 2022 Standard Specification for Copper-Beryllium Welded Heat Exchanger and Condenser Tube (UNS No. C17510)
ASTM B 247M : 2020 Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric)
ASTM B 221M : 2021 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)
ASTM B 209/B209M : 2021 : REV A Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
ASTM B 210/B210M : 2019 : REV A Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
ASTM B 768 : 2022 Standard Specification for Copper-Cobalt-Beryllium Alloy and Copper-Nickel-Beryllium Alloy Strip and Sheet
ASTM B 221 : 2021 Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
ASTM B 49 : 2020 Standard Specification for Copper Rod for Electrical Purposes
ASTM B 236/B236M : 2023 Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars)
ASTM E 2338 : 2022 Standard Practice for Characterization of Coatings Using Conformable Eddy Current Sensors without Coating Reference Standards
ASTM B 211/B211M : 2023 Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
ASTM B 248 : 2022 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
ASTM B 870 : 2021 Standard Specification for Copper-Beryllium Alloy Forgings and Extrusions (UNS Nos. C17500, C17510, and C17540)
ASTM B 441 : 2022 Standard Specification for Copper-Cobalt-Beryllium Alloy, Copper-Nickel-Beryllium Alloy, Copper-Nickel-Lead-Beryllium Alloy, and Copper-Nickel-Cobalt Alloy Rod and Bar

ASTM E 1316 : 2022 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1251 : 2007 Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry
ASTM E 2371 : 2013 Standard Test Method for Analysis of Titanium and Titanium Alloys by Direct Current Plasma and Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Test Methodology)
ASTM E 1316 : 2011 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2015 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2009 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2008 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2010 : REV C Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2020 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2017 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2013 : REV C Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2000 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 543 : 2021 Standard Specification for Agencies Performing Nondestructive Testing
ASTM E 18 : 2022 Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM E 1316 : 2019 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1251 : 1994 : R1999 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Argon Atmosphere, Point-to-Plane, Unipolar Self-Initiating Capacitor Discharge
ASTM E 10 : 2023 Standard Test Method for Brinell Hardness of Metallic Materials
ASTM E 10 : 2001 Standard Test Method for Brinell Hardness of Metallic Materials
ASTM E 1316 : 2014 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2013 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2018 Standard Terminology for Nondestructive Examinations
ASTM E 1251 : 2017 Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
ASTM E 18 : 2020 Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM E 1316 : 2011 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2007 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2015 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2019 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2013 : REV D Standard Terminology for Nondestructive Examinations
ASTM E 122 : 2017 : R2022 Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process
ASTM E 122 : 2017 Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process
ASTM E 1316 : 2000 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2019 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2001 Standard Terminology for Nondestructive Examinations
ASTM E 105 : 2021 Standard Guide for Probability Sampling of Materials
ASTM E 1316 : 2003 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2018 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2006 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2016 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV D Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2002 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1251 : 2004 Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry
ASTM E 1316 : 2014 : EDT 1 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2010 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2022 Standard Terminology for Nondestructive Examinations
ASTM E 2371 : 2004 Standard Test Method for Analysis of Titanium and Titanium Alloys by Atomic Emission Plasma Spectrometry (Withdrawn 2013)
ASTM E 1316 : 2013 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 18 : 2019 Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM E 1251 : 2011 Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
ASTM E 105 : 2016 Standard Practice for Probability Sampling of Materials
ASTM E 1316 : 2017 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2016 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2009 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2002 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2004 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2007 : REV C Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2010 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2013 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2023 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 Standard Terminology for Nondestructive Examinations
ASTM E 1251 : 2017 : REV A Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
ASTM E 1316 : 2007 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2005 Standard Terminology for Nondestructive Testing
ASTM E 1316 : 2004 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV C Standard Terminology for Nondestructive Examinations
ASTM E 2371 : 2021 : REV A Standard Test Method for Analysis of Titanium and Titanium Alloys by Direct Current Plasma and Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Test Methodology)
ASTM E 10 : 2018 Standard Test Method for Brinell Hardness of Metallic Materials
ASTM E 1316 : 2007 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2023 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2023 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2012 Standard Terminology for Nondestructive Examinations
ASTM E 2371 : 2021 Standard Test Method for Analysis of Titanium and Titanium Alloys by Direct Current Plasma and Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Test Methodology)

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.