• There are no items in your cart

ASTM E 1030 : 2005

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Radiographic Examination of Metallic Castings
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

12-01-2005

CONTAINED IN VOL. 03.03, 2015 Defines a uniform procedure for radiographic examination of metallic castings using radiographic film as the recording medium.

1.1 This test method provides a uniform procedure for radiographic examination of metallic castings using radiographic film as the recording medium.

1.2 Due to the many complex geometries and part configurations inherent with cast products, it is necessary to recognize potential limitations associated with obtaining complete radiographic coverage on castings. Radiography of areas where geometry or part configuration does not allow achievement of complete coverage with practical radiographic methods shall be subject to mutual agreements between purchaser and supplier. The use of alternative nondestructive methods for areas that are not conducive to practical radiography shall also be specifically agreed upon between purchaser and supplier.

1.3 The radiographic method is highly sensitive to volumetric discontinuities that displace a detectable volume of cast material. Discontinuities that do not displace an appreciable volume of material, however, such as cracks or other planar-type indications, may not be detected with radiography unless the radiation beam is coincidentally aligned with the planar orientation of the discontinuity. In view of this limitation, it may be considered appropriate to use the radiographic method in conjunction with additional nondestructive methods that maintain reliable detection capabilities for these types of discontinuities. The use of additional methods shall be specifically agreed upon between the purchaser and supplier.

1.4 The radiographic techniques stated herein provide adequate assurance for defect detectability; however, it is recognized that, for special applications, specific techniques using more or less stringent requirements may be required than those specified. In these cases, the use of alternate radiographic techniques shall be as agreed upon between purchaser and supplier (also see Section ).

1.5 The values stated in inch-pound units are to be regarded as standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
E 07
DocumentType
Test Method
Pages
11
ProductNote
Reconfirmed 2005
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 2104 : 2015 Standard Practice for Radiographic Examination of Advanced Aero and Turbine Materials and Components
ASTM E 543 : 2015 Standard Specification for Agencies Performing Nondestructive Testing
ASTM F 2895 : 2015 Standard Practice for Digital Radiography of Cast Metallic Implants
ASTM E 94/E94M : 2017 Standard Guide for Radiographic Examination Using Industrial Radiographic Film
ASTM F 629 : 2015 Standard Practice for Radiography of Cast Metallic Surgical Implants
ASTM E 2033 : 2017 Standard Practice for Radiographic Examination Using Computed Radiography (Photostimulable Luminescence Method)
ASTM E 1742/E1742M : 2018 Standard Practice for Radiographic Examination

ASTM E 1254 : 2013 Standard Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
EN 444:1994 Non-destructive testing - General principles for radiographic examination of metallic materials by X- and gamma-rays
ASTM E 689 : 2015 : REDLINE Standard Reference Radiographs for Ductile Iron Castings
ASTM E 446 : 2015 : REDLINE Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness
ASNT SNT TC 1A : 2016 TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ASTM E 186 : 2015 : REDLINE Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings
ASTM E 802 : 2015 : REDLINE Standard Reference Radiographs for Gray Iron Castings Up to 4<fraction><num>1</num><den>2</den> </fraction> in. (114 mm) in Thickness
NAS410:2003 NAS CERTIFICATION & QUALIFICATION OF NONDESTRUCTIVE TEST PERSONNEL
ASTM E 155 : 2015 : REDLINE Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings
ASTM E 505 : 2015 : REDLINE Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
ISO 5579:2013 Non-destructive testing Radiographic testing of metallic materials using film and X- or gamma rays Basic rules
ASNT CP 189 : 2016 QUALIFICATION AND CERTIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ASTM E 1320 : 2015 : REDLINE Standard Reference Radiographs for Titanium Castings
ASTM E 192 : 2015 : REDLINE Standard Reference Radiographs of Investment Steel Castings for Aerospace Applications
ASTM E 999 : 2015 : REDLINE Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing
ASTM E 272 : 2015 : REDLINE Standard Reference Radiographs for High-Strength Copper-Base and Nickel-Copper Alloy Castings
ASTM E 280 : 2015 : REDLINE Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings
ASTM E 543 : 2015 : REDLINE Standard Specification for Agencies Performing Nondestructive Testing
ASTM E 1079 : 2016 : REDLINE Standard Practice for Calibration of Transmission Densitometers
ASTM E 310 : 2015 : REDLINE Standard Reference Radiographs for Tin Bronze Castings

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.