ASTM E 1444 : 2005
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Practice for Magnetic Particle Testing
Available format(s)
Hardcopy , PDF
Superseded date
11-11-2014
Language(s)
English
Published date
03-01-2005
CONTAINED IN VOL. 03.03, 2005 Gives minimum requirements for magnetic particle examination used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material.
1.1 This practice establishes minimum requirements for magnetic particle examination used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material. Guide E 709 can be used in conjunction with this practice as a tutorial.
Note 1—This Practice replaces MIL-STD-1949.
1.2 The magnetic particle examination method is used to detect cracks, laps, seams, inclusions, and other discontinuities on or near the surface of ferromagnetic materials. Magnetic particle examination may be applied to raw material, billets, finished and semi-finished materials, welds, and in-service parts. Magnetic particle examination is not applicable to non-ferromagnetic metals and alloys such as austenitic stainless steels. See Appendix X6 for additional information.
1.3 All areas of this Practice may be open to agreement between the Cognizant Engineering Organization and the supplier, or specific direction from the Cognizant Engineering Organization.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
E 07
|
| DevelopmentNote |
Supersedes SAE AMS 2640 (07/1999)
|
| DocumentType |
Standard Practice
|
| Pages |
20
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE AMS 3044G : 2014 | MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, DRY POWDER |
| SAE AMS 2694 : 2013 | IN-PROCESS WELDING OF CASTINGS |
| SAE AMS 5349 : 2013 | STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS, 13CR, FREE MACHINING; HARDENED AND TEMPERED |
| SAE ARP 5796 : 2013 | FLIGHT CRITICAL CONTROL VALVES, MILITARY AIRCRAFT |
| SAE AMS 3040 : 2014 | MAGNETIC PARTICLES, NONFLUORESCENT, DRY METHOD |
| SAE MA 2005 : 2015 | TUBE FITTINGS, AEROSPACE FLUID SYSTEMS, SEPARABLE, FOR 24 DEGREE CONE, GENERAL SPECIFICATION, METRIC |
| SAE AMS 5336 : 2017 | STEEL, INVESTMENT CASTINGS, 0.95CR - 0.20MO (0.25 - 0.35C) (4130 MOD) NORMALIZED OR NORMALIZED AND TEMPERED |
| SAE AMS 5346 : 2014 | STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS, 15CR - 4.6NI - 0.22CB (NB) - 2.8CU, SOLUTION AND PRECIPITATION HEAT TREATED (H925), 180 KSI (1241 MPA) TENSILE STRENGTH (15-5) |
| MIL-STD-2175 Revision A:1993 | CASTING, CLASSIFICATION AND INSPECTION OF |
| I.S. EN 16603-32-01:2014 | SPACE ENGINEERING - FRACTURE CONTROL |
| SAE AMS 2681 : 2014 | WELDING, ELECTRON-BEAM |
| MIL-DTL-82876 Revision A:1995 | CATAPULT, AIRCRAFT EJECTION SEAT, CKU-5B/A ASSEMBLY |
| UNI EN 4700-006 : 2011 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| SAE AS 8952 : 2005 | BEARINGS, ROLLER, ROD END, ANTIFRICTION SELF-ALIGNING |
| MIL-PRF-32316 Base Document:2008 | RIFLE, 7.62 MM: SEMI-AUTOMATIC SNIPER SYSTEM (SASS) - M110 |
| MIL-DTL-63997 Revision C:2009 | Rifle, 5.56 Millimeter: M16A2 |
| MIL-DTL-23599 Revision C:2017 | Hook, Rescue |
| SAE AMS 5334 : 2013 | STEEL, INVESTMENT CASTINGS, 0.50CR - 0.55NI - 0.20MO (0.25 - 0.35C) (SAE 8630 MOD), NORMALIZED AND TEMPERED |
| MIL-DTL-70599 Revision B:2009 | Carbine, 5.56 Millimeter: M4 |
| FF-N-836 Revision E:1994 | Nut: Square, Hexagon, Cap, Slotted, Castle, Knurled, Welding and Single Ball Seat |
| MIL-DTL-12560 Revision K:2013 | ARMOR PLATE, STEEL, WROUGHT, HOMOGENEOUS (FOR USE IN COMBAT-VEHICLES AND FOR AMMUNITION TESTING) |
| MIL-PRF-32327 Base Document:2009 | Rifle, Caliber .50:Sniper W/Day Optic Sight and Carrying Cases - M107 |
| API 5ST:2010 | SPECIFICATION FOR COILED TUBING |
| I.S. EN 16602-70-46:2014 | SPACE PRODUCT ASSURANCE - REQUIREMENTS FOR MANUFACTURING AND PROCUREMENT OF THREADED FASTENERS |
| PREN 4700-005 : 200P2 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK |
| AWS D3.6M : 2010 | UNDERWATER WELDING CODE |
| PREN 4700-006 : 200P2 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| SAE AMS 2303 : 2016 | STEEL CLEANLINESS, AIRCRAFT QUALITY, MARTENSITIC CORROSION-RESISTANT STEELS, MAGNETIC PARTICLE INSPECTION PROCEDURE |
| SAE AS 45909 : 2015 | STUD, LOCKED IN, RING LOCKED, SERRATED, GENERAL SPECIFICATION FOR |
| AWS D17.1 : 2001 | SPECIFICATION FOR FUSION WELDING FOR AEROSPACE APPLICATIONS |
| SAE AMS 6365 : 2014 | STEEL TUBING, SEAMLESS, 0.95CR - 0.20MO (0.33 - 0.38C) (SAE 4135), NORMALIZED OR STRESS RELIEVED |
| ASCE/SEI 19 10 : 2010 | STRUCTURAL APPLICATIONS OF STEEL CABLES FOR BUILDINGS |
| SAE AMS 2442 : 2012 | MAGNETIC PARTICLE ACCEPTANCE CRITERIA FOR PARTS |
| ASTM E 543 : 2015 | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM E 45 : 2018 : REV A | Standard Test Methods for Determining the Inclusion Content of Steel |
| ASTM E 3022 : 2018 | Standard Practice for Measurement of Emission Characteristics and Requirements for LED UV-A Lamps Used in Fluorescent Penetrant and Magnetic Particle Testing |
| ASTM F 519 : 2018 | Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments |
| ASTM E 2297 : 2015 | Standard Guide for Use of UV-A and Visible Light Sources and Meters used in the Liquid Penetrant and Magnetic Particle Methods |
| MIL-DTL-63245 Revision C:2008 | Projectile 155 Millimeter: HE, Metal Parts Assembly, M795 |
| DEFSTAN 00-970(PT0)/9(2012) : 2012 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/17(2016) : 2016 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/7(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/14(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| MIL-STD-2219 Revision A:2005 | FUSION WELDING FOR AEROSPACE APPLICATIONS |
| MIL-DTL-70329 Revision A:2009 | Nut, Plain, Round, Ball and Roller Bearings, Metric, General Specification for |
| DEFSTAN 00-970(PT0)/11(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/13(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/15(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/12(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| MIL-DTL-5523 Revision E:2011 | VALVE; RELIEF, HYDRAULIC PRESSURE |
| MIL-DTL-25027 Revision H:1997 | NUT, SELF-LOCKING, 250 DEG F, 450 DEG F, AND 850 DEG F |
| FF-S-85 Revision D:2005 | Screw, Cap, Slotted and Hexagon Head |
| DEFSTAN 00-970(PT0)/8(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/16(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/10(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| MIL-DTL-48568 Revision D:1996 | CATAPULT, AIRCRAFT EJECTION SEAT, CKU-7/A ASSEMBLY |
| BS EN 4700-006:2010 | Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Pre-production and production forgings |
| API 2F : 1997 : R2015 | SPECIFICATION FOR MOORING CHAIN |
| MIL-STD-867 Revision C:2008 | TEMPER ETCH INSPECTION |
| MIL-HDBK-728-4 Revision A:1993 | MAGNETIC PARTICLE TESTING |
| EN 4700-002:2016 | Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 002: Bar and section |
| SAE AMS 6361 : 2014 | STEEL TUBING, SEAMLESS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) 125 KSI (862 MPA) TENSILE STRENGTH |
| BS EN 4700-005:2010 | Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Forging stock |
| BS EN 16602-70-46:2014 | Space product assurance. Requirements for manufacturing and procurement of threaded fasteners |
| AGMA 2004 : C | GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL |
| NF EN 4700-005 : 2012 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK |
| MIL-DTL-1298 Revision D Interim Revision:2007 | GUN, MACHINE; CALIBER .50, BROWNING, M2, HEAVY BARREL |
| API 5ST : 2010 : R2015 | SPECIFICATION FOR COILED TUBING |
| SAE AMS I 83387 : 2016 | INSPECTION PROCESS, MAGNETIC RUBBER |
| MIL-STD-866 Revision C:2007 | Grinding of Chrome Plated Steel and Steel Parts Heat Treated to 180,000 PSI or Over |
| MIL-PRF-38170 Revision H:2000 | TANK, MOBILE STORAGE, LIQUID OXYGEN TMU-27/M |
| SAE AS 7459 : 2015 | BOLTS AND SCREWS, STEEL UNS K14675 TENSILE STRENGTH 195 KSI FATIGUE AND STRESS-RUPTURE RATED PROCUREMENT SPECIFICATION |
| SAE AMS 5343 : 2014 | STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS, 16CR - 4.1NI - 0.28CB (NB) - 3.2CU, HOMOGENIZATION, SOLUTION, AND PRECIPITATION HEAT TREATED (H1000), 150 KSI (1034 MPA) TENSILE STRENGTH (17-4) |
| MIL-DTL-32309 Base Document:2009 | Rifle, 5.56 Millimeter: M16A4 |
| MIL-DTL-85110 Revision B:1997 | BAR, REPEATABLE RELEASE HOLDBACK (RRHB), AIRCRAFT LAUNCHING, GENERAL REQUIREMENT FOR |
| SAE MA 1573 : 2016 | NUT, SELF-LOCKING, STEEL, CLASS 1100 MPA/235 DEGREES C, MJ THREAD PROCUREMENT SPECIFICATION FOR, METRIC |
| SAE AMS 6360 : 2013 | STEEL TUBING, SEAMLESS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), NORMALIZED OR STRESS RELIEVED |
| ASTM E 543 : 2015 : REDLINE | Standard Specification for Agencies Performing Nondestructive Testing |
| MIL-HDBK-115 Revision C:2016 | U.S. ARMY REVERSE ENGINEERING HANDBOOK (GUIDELINES AND PROCEDURES) |
| SBAC TS 108 : 5 | MANUFACTURING SPECIFICATION FOR STUDS, BOLTS AND SCREWS IN BS S159 MATERIAL 1100 MPA (159,000 LBF/IN[2]) TENSILE AT ROOM TEMPERATURE (FOR WHICH FORGING IS OPTIONAL AND QUALIFICATION NOT A REQUIREMENT) |
| SAEITC TS 22 ISSUE 10 : 2008 | MANUFACTURING SPECIFICATION FOR BOLTS, 1100 MPA (159,000 LBF/IN[2]) - ULTIMATE TENSILE STRENGTH - MINIMUM AT ROOM TEMPERATURE |
| SBAC TS 145 : 4 | TECHNICAL SPECIFICATION NO. TS145 - MANUFACTURING SPECIFICATION FOR BOLTS (UNIFIED THREADS) HEAT RESISTING ALLOY STEEL FV535, CLASSIFICATION RM >= 1000 MPA (145,000 LBF/IN[2]) @ TA/+550 DEGREES C |
| SAE AMS 5340 : 2018 | STEEL, CORROSION RESISTANT, INVESTMENT CASTINGS, 14CR - 4.25NI - 2.25MO - 0.25CB - 3.25CU, HOMOGENIZATION AND SOLUTION HEAT TREATED |
| ASTM E 3022 : 2015 | Standard Practice for Measurement of Emission Characteristics and Requirements for LED UV-A Lamps Used in Fluorescent Penetrant and Magnetic Particle Testing |
| DOD-W-63546 Revision A:1982 | WASHER, KEY, METRIC GENERAL SPECIFICATION FOR |
| MIL-DTL-60584 Revision B:2006 | Projectile,155 Millimeter - Smoke, WP, Metal Parts Assembly, M110A2 |
| MIL-PRF-27720 Revision G:2009 | TANK, STORAGE, LIQUID OXYGEN/LIQUID NITROGEN, TMU-24/E |
| MIL-DTL-3241 Revision F:2010 | REELS, CABLE (REELS DR-5(), DR-7(), DR-B(), RC-453()/G, RL-159()/U) |
| NASA STD 5009 : 2008 | NONDESTRUCTIVE EVALUATION REQUIREMENTS FOR FRACTURE-CRITICAL METALLIC COMPONENTS - MEASUREMENT SYSTEM IDENTIFICATION: METRIC (INCH-POUND) |
| BS EN 4700-002:2016 | Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Bar and section |
| UNI EN 4700-005 : 2011 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK |
| 15/30269176 DC : 0 | BS ISO 6336-5 - CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS - PART 5: STRENGTH AND QUALITY OF MATERIALS |
| SAE AIR 4777 : 2013(R 2018) | NONDESTRUCTIVE INSPECTION (NDI) METHODS USED DURING PRODUCTION AND OPERATION OF AIRCRAFT WHEELS AND BRAKES |
| MIL-DTL-85405 Revision A:1997 | TRAILER, MUNITIONS, MHU-185/M |
| MIL-HDBK-1941 Base Document:1998 | METAL-ARC WELDING OF HOMOGENEOUS ARMOR |
| SAE ARP 5812 : 2017 | ACTUATORS, LINEAR MECHANICAL, GENERAL SPECIFICATION GUIDE |
| SAE AMS 2304 : 2015 | STEEL CLEANLINESS, SPECIAL AIRCRAFT-QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE |
| SAE AMS 5344 : 2013 | STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS, 16CR - 4.1NI - 0.28CB - 3.2CU, HOMOGENIZATION, SOLUTION, AND PRECIPITATION HEAT TREATED (H900), 180 KSI (1241 MPA) TENSILE STRENGTH (17-4) |
| NF EN 4700-006 : 2012 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| MIL-DTL-32127 Revision A:2005 | CATAPULT, AIRCRAFT EJECTION SEAT, CKU-5C/A ASSEMBLY |
| AWS B5.4 : 2005 | SPECIFICATION FOR THE QUALIFICATION OF WELDER TEST FACILITIES |
| SAE ARP 1281 : 2002 | ACTUATORS: AIRCRAFT FLIGHT CONTROLS, POWER OPERATED, HYDRAULIC, GENERAL SPECIFICATION FOR |
| SAE AMS 5338 : 2017 | STEEL, INVESTMENT CASTINGS, 0.95CR - 0.20MO (0.35 - 0.45C) (4140 MOD), NORMALIZED OR NORMALIZED AND TEMPERED |
| SAE ARP 5600 : 2015 | DISPOSITION OF DAMAGED WHEELS INVOLVED IN ACCIDENTS/INCIDENTS |
| SAE AMS 2685 : 2017 | WELDING, TUNGSTEN ARC, INERT GAS, (GTAW METHOD) |
| SAE ARP 5936 : 2016 | LANDING GEAR STORAGE |
| SAE ARP 4058 : 2017 | GENERAL SPECIFICATION GUIDE FOR MECHANICAL GEARED ROTARY ACTUATORS |
| SAE AMS 2301 : 2015 | STEEL CLEANLINESS, AIRCRAFT QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE |
| SAE AMS 2300 L : 2015 | STEEL CLEANLINESS, PREMIUM AIRCRAFT-QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE |
| SAE AMS 5342 : 2014 | STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS, 16CR - 4.1NI - 0.28CB (NB) - 3.2CU, HOMOGENIZATION, SOLUTION, AND PRECIPITATION HEAT TREATED (H1100), 130 KSI (896 MPA) TENSILE STRENGTH (17-4) |
| SAE AMS 3045 : 2014 | MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, OIL VEHICLE, READY-TO-USE |
| I.S. EN 4700-006:2010 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| ISO 6336-5:2016 | Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials |
| BS EN 16603-32-01:2014 | Space engineering. Fracture control |
| NASA PRC 6505 : 2011 | PROCESS SPECIFICATION FOR MAGNETIC PARTICLE INSPECTION |
| NASA STD 5005(INT) : 2007 | THE DESIGN AND FABRICATION OF GROUND SUPPORT EQUIPMENT |
| NASA KSC DE 512-SM : 2012 | FACILITY SYSTEMS, GROUND SUPPORT SYSTEMS, AND GROUND SUPPORT EQUIPMENT GENERAL DESIGN REQUIREMENTS |
| NASA STD 5009(INT) : 2006 | NONDESTRUCTIVE EVALUATION REQUIREMENTS FOR FRACTURE CRITICAL METALLIC COMPONENTS |
| SAE AS 4792 : 2013 | WATER CONDITIONING AGENTS FOR AQUEOUS MAGNETIC PARTICLE INSPECTION |
| MIL-DTL-71172 Revision B:2005 | CYLINDER, RECUPERATOR, RECOIL, M119A1/A2 HOWITZER LIGHT, TOWED: 105 MM |
| NAS496:2002 | BOLTS - INTERNAL WRENCHING |
| MIL-DTL-44481 Revision A:1996 | RELEASE, CARGO PARACHUTE, AIRDROP, M-3 |
| AGMA 923 : B | METALLURGICAL SPECIFICATIONS OF STEEL GEARING |
| MIL-DTL-5498 Revision G:2013 | ACCUMULATORS, HYDRAULIC, CYLINDRICAL 3000 PSI, AIRCRAFT |
| MIL-DTL-85537 Revision A:1997 | TRAILER, MUNITIONS, AERO 51C |
| MIL-DTL-71186 Revision A:2009 | Carbine, 5.56 Millimeter: M4A1 |
| SAE AS 7470 : 2012 | BOLTS AND SCREWS, STEEL, CORROSION AND MODERATE HEAT RESISTANT HEAT TREATED, ROLL THREADED |
| API 20D : 2013 | NONDESTRUCTIVE EXAMINATION SERVICES FOR EQUIPMENT USED IN THE PETROLEUM AND NATURAL GAS INDUSTRY |
| SAE AMS 2175 : 2010 | CASTINGS, CLASSIFICATION AND INSPECTION OF |
| SAE AMS 6362 : 2014 | STEEL TUBING, SEAMLESS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), 150 KSI (1034 MPA) TENSILE STRENGTH |
| API 2X : 2004 : R2015 | RECOMMENDED PRACTICE FOR ULTRASONIC AND MAGNETIC EXAMINATION OF OFFSHORE STRUCTURAL FABRICATION AND GUIDELINES FOR QUALIFICATION OF TECHNICIANS |
| SAE AMS 5368 : 2012 | STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS 15CR - 4.0NI - 2.3MO - 0.09N SOLUTION HEAT TREATED |
| SAE AIR 1594 : 2010 | PLAIN BEARING SELECTION FOR LANDING GEAR APPLICATIONS |
| SAE AMS 3041 : 2014 | MAGNETIC PARTICLES, NONFLUORESCENT, WET METHOD, OIL VEHICLE, READY-TO-USE |
| API 2F : 1997 | SPECIFICATION FOR MOORING CHAIN |
| SAE AMS 6373 : 2016 | STEEL, WELDED TUBING, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| SAE AS 3071 : 2012 | ACCEPTANCE CRITERIA - MAGNETIC PARTICLE, FLUORESCENT PENETRANT, AND CONTRAST DYE PENETRANT INSPECTION |
| SAE AS 5282 : 2015 | TOOL STEEL RING FOR MAGNETIC PARTICLE INSPECTION |
| SAE AMS 5339 : 2017 | STEEL, MARAGING, INVESTMENT CASTINGS, 17NI - 10CO - 4.6MO - 0.30TI - 0.06AL, VACUUM MELTED, HOMOGENIZED, OVERAGED AND SOLUTION HEAT TREATED |
| SAE AS 39901 : 2012 | BEARINGS, ROLLER, NEEDLE, AIRFRAME, ANTIFRICTION, INCH |
| SAE AMS 5352 : 2015 | STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS, 17CR - 0.55MO (0.95 - 1.20C), ANNEALED |
| I.S. EN 4700-005:2010 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK |
| EN 4700-005:2010 | Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 005: Forging stock |
| MIL-DTL-5508 Revision C:2007 | FUSES, AIRCRAFT AUTOMATIC QUANTITY-MEASURING, HYDRAULIC |
| EN 16602-70-46:2014 | Space product assurance - Requirements for manufacturing and procurement of threaded fasteners |
| EN 4700-006:2010 | Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 006: Pre-production and production forgings |
| SAE AMS 5333 : 2017 | STEEL, INVESTMENT CASTINGS, 0.50CR - 0.55NI - 0.25MO (0.11 - 0.17C) (SAE 8615), NORMALIZED |
| SAE AS 7949 : 2004 | BEARINGS, BALL, AIRFRAME, ANTIFRICTION, GENERAL STANDARD |
| MIL-DTL-85097 Revision E:2000 | USN/USMC PROPELLANT ACTUATED DEVICES (PADS) - GENERAL SPECIFICATION FOR |
| API 5ST CHINESE : 2010 | SPECIFICATION FOR COILED TUBING |
| MIL P 63245 : B | PROJECTILE, 155 MM, HE, M795, METAL PARTS ASSEMBLY |
| SAE AMS 3042 : 2014 | MAGNETIC PARTICLES, NONFLUORESCENT, WET METHOD, DRY POWDER |
| API 2F : 1997 : R2010 | SPECIFICATION FOR MOORING CHAIN |
| MIL-DTL-70446 Revision B:2007 | MACHINE GUN, 5.56 MM: M249 |
| MIL-DTL-70446 Revision C:2008 | MACHINE GUN, 5.56 MM: M249 |
| API 2X : 2004 | RECOMMENDED PRACTICE FOR ULTRASONIC AND MAGNETIC EXAMINATION OF OFFSHORE STRUCTURAL FABRICATION AND GUIDELINES FOR QUALIFICATION OF TECHNICIANS |
| I.S. EN 4700-002:2016 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| MIL-DTL-46177 Revision C:1998 | ARMOR, STEEL PLATE AND SHEET, WROUGHT, HOMOGENEOUS (1/8 TO LESS THAN 1/4 INCH THICK) |
| NASA PRC 0008 : 2004 | PROCESS SPECIFICATION FOR THE QUALIFICATION OF MANUAL ARC WELDERS |
| A-L-2924 Base Document:1997 | LIFTING, LAUNCHING, AND SIDE CARRYING EQUIPMENT FOR PONTOONS ON 1179 CLASS LST VESSELS |
| BS ISO 6336-5:2016 | Calculation of load capacity of spur and helical gears Strength and quality of materials |
| MIL-DTL-32129 Revision A:2009 | CATAPULT, AIRCRAFT EJECTION SEAT, CKU-7A/A ASSEMBLY |
| NAS159:2002 | BOLT - INTERNAL WRENCHING - AIRCRAFT |
| API 2SF : 2013 | MANUFACTURE OF STRUCTURAL STEEL FORGINGS FOR PRIMARY OFFSHORE APPLICATIONS |
| MIL-STD-1501 Revision F:2011 | Chromium Plating, Low Embrittlement, Electrodeposition |
| SAE AMS5337E : 2017 | STEEL, MARAGING, INVESTMENT CASTINGS, 18.5NI - 9.0CO - 5.0MO - 0.70TI - 0.12AL, VACUUM MELTED, HOMOGENIZED, OVERAGED, AND SOLUTION HEAT TREATED |
| MIL-DTL-81944 Revision C:1997 | TRAILER, MUNITIONS, SMALL (MHU-126 A/M) |
| ASTM E 2297 : 2015 : REDLINE | Standard Guide for Use of UV-A and Visible Light Sources and Meters used in the Liquid Penetrant and Magnetic Particle Methods |
| MIL-DTL-62567 Revision D:2010 | TORSION BAR, SUSPENSION |
| SAE AMS 5354 : 2012 | STEEL, CORROSION AND HEAT RESISTANT, INVESTMENT CASTINGS, 13CR - 2.0NI - 3.0W, HARDENED AND TEMPERED TO 32 - 38 HRC |
| SAE AMS 3046 : 2014 | MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, OIL VEHICLE, AEROSOL PACKAGED |
| SAE MA 3376 : 2018 | Bolts & Screws, UNS G87400 Tensile Strength 860 MPa & 1000 MPa Procurement Specification, Metric |
| MIL-DTL-14852 Revision D:2009 | PROJECTILE, 105 MM, ILLUMINATING, M314A3 AND PROJECTILE, 105 MM, INFRARED ILLUMINATING, M1064 METAL PARTS ASSEMBLY |
| SAE AS 5447 : 2012 | ACCEPTANCE CRITERIA FOR NUTS - MAGNETIC, PARTICLE, FLUORESCENT PENETRANT, AND VISIBLE PENETRANT EXAMINATION |
| SAE AMS 2453 : 2015 | LOW STRESS GRINDING OF STEEL PARTS HEAT TREATED TO 180 KSI OR OVER, AND LOW STRESS GRINDING OF CHROME PLATING APPLIED TO STEEL PARTS HEAT TREATED TO 180 KSI OR OVER |
| SAE AMS 3043 : 2014 | MAGNETIC PARTICLES, NONFLUORESCENT, WET METHOD, OIL VEHICLE, AEROSOL PACKAGED |
| SAE AIR 4012 : 2012 | USAF AIRCRAFT WHEELS |
| SAE AMS7301J:2003(S2017) | Steel, Highly-Stressed Springs 0.95Cr - 0.20V (0.48 - 0.53C) (SAE 6150) Case Hardened(STABILIZED Aug 2017) |
| PREN 4700-002 : 200P3 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| API TR 17TR8 : 2018 | HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES |
| SAE AMS 5347 : 2014 | STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS, 15CR - 4.6NI - 0.22CB (NB) - 2.8CU, SOLUTION AND PRECIPITATION HEAT TREATED (H1000), 150 KSI (1034 MPA) TENSILE STRENGTH (15-5) |
| SAE AS 7114/2 : 2008 | NADCAP REQUIREMENTS FOR NONDESTRUCTIVE TESTING MAGNETIC PARTICLE SURVEY |
| IEEE 1415 : 2006 | INDUCTION MACHINERY MAINTENANCE TESTING AND FAILURE ANALYSIS |
| SAE AMS 5353E : 2007(R2015) | STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS, 16CR - 1.8NI - 0.08N, AS CAST |
| SAE AMS 5387 : 2015 | ALLOY, CORROSION AND HEAT RESISTANT, INVESTMENT CASTINGS, 60CO - 29CR - 4.5W, AS CAST |
| SAE AMS6474B:2008(S2018) | FORGINGS, HARDENABLE STEELS AND CORROSION-RESISTANT STEELS HEAT-TREATED, FINISHED-PART PROPERTIES SHORT-TRANSVERSE TENSILE STRENGTH AND FRACTURE TOUGHNESS |
| SAE AMS STD 2175 : 2003 | CASTINGS, CLASSIFICATION AND INSPECTION OF |
| EN 16603-32-01:2014 | Space engineering - Fracture control |
| SAE AMS 3040 : 2014 | MAGNETIC PARTICLES, NONFLUORESCENT, DRY METHOD |
| FED-STD-313 Revision D:1996 | MATERIAL SAFETY DATA, TRANSPORTATION DATA AND DISPOSAL DATA FOR HAZARDOUS MATERIALS FURNISHED TO GOVERNMENT ACTIVITIES |
| SAE AMS 3045 : 2014 | MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, OIL VEHICLE, READY-TO-USE |
| ASNT SNT TC 1A : 2016 | TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
| SAE AMS 2641 : 2015 | VEHICLE, MAGNETIC PARTICLE INSPECTION, PETROLEUM BASE |
| NAS410:2003 | NAS CERTIFICATION & QUALIFICATION OF NONDESTRUCTIVE TEST PERSONNEL |
| SAE AMS 3042 : 2014 | MAGNETIC PARTICLES, NONFLUORESCENT, WET METHOD, DRY POWDER |
| SAE AMS 3043 : 2014 | MAGNETIC PARTICLES, NONFLUORESCENT, WET METHOD, OIL VEHICLE, AEROSOL PACKAGED |
| SAE AS 4792 : 2013 | WATER CONDITIONING AGENTS FOR AQUEOUS MAGNETIC PARTICLE INSPECTION |
| MIL-STD-2175 Revision A:1993 | CASTING, CLASSIFICATION AND INSPECTION OF |
| SAE AMS 3041 : 2014 | MAGNETIC PARTICLES, NONFLUORESCENT, WET METHOD, OIL VEHICLE, READY-TO-USE |
| SAE AMS 3044G : 2014 | MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, DRY POWDER |
| ANSI/NCSL Z540 1 : 94(R2002) | CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS |
| SAE AMS I 83387 : 2016 | INSPECTION PROCESS, MAGNETIC RUBBER |
| ASNT CP 189 : 2016 | QUALIFICATION AND CERTIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
| CFR 29(PT1910.1000 TO END) : 0 | LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR |
| SAE AMS 5062 : 2013 | STEEL, LOW CARBON, BARS, FORGINGS, TUBING, SHEET, STRIP, AND PLATE, 0.25 CARBON, MAXIMUM |
| SAE AS 5371 : 1998 | REFERENCE STANDARDS NOTCHED SHIMS FOR MAGNETIC PARTICLE INSPECTION |
| ASTM E 543 : 2015 : REDLINE | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| ASTM A 275/A275M : 2015-05 | PRACTICE FOR MAGNETIC PARTICLE EXAMINATION OF STEEL FORGINGS |
| ISO 10012-1:1992 | Quality assurance requirements for measuring equipment Part 1: Metrological confirmation system for measuring equipment |
| FED-STD-595 Revision C:2008 | COLORS USED IN GOVERNMENT PROCUREMENT |
| SAE AMS 3046 : 2014 | MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, OIL VEHICLE, AEROSOL PACKAGED |
| A-A-59230 Base Document:1998 | FLUID, MAGNETIC PARTICLE INSPECTION, SUSPENSION |
| SAE AS 5282 : 2015 | TOOL STEEL RING FOR MAGNETIC PARTICLE INSPECTION |
US$83.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.