ASTM E 2918 : 2018 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
08-21-2023
English
01-17-2019
This test method provides procedures for validating temperature and length change measurements of thermomechanical analyzers (TMA) and analytical methods based upon the measurement of temperature and length change.
1.1This test method provides procedures for validating temperature and length change measurements of thermomechanical analyzers (TMA) and analytical methods based upon the measurement of temperature and length change. Performance parameters include temperature repeatability, linearity, and bias; and dimension change repeatability, detection limit, quantitation limit, linearity, and bias.
1.2Validation of apparatus performance and analytical methods is a necessary requirement for quality initiatives. Results may also be used for legal purposes.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
E 37
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM E 473 : 2023 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1142 : 2022 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2022 : REV D | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1363 : 1997 : EDT 1 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 2161 : 2015 : R2019 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2161 : 2023 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2011 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2012 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2022 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2015 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 1997 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2021 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2013 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 2161 : 2022 : REV B | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2013 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2113 : 2000 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 1970 : 2011 | Standard Practice for Statistical Treatment of Thermoanalytical Data |
| ASTM E 1970 : 2000 | Standard Practice for Statistical Treatment of Thermoanalytical Data |
| ASTM E 1142 : 2004 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2022 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2022 : REV C | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2113 : 2002 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 473 : 2022 : REV B | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1142 : 2006 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2018 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1142 : 2015 : R2020 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2021 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2161 : 2022 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2021 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1363 : 2016 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 2113 : 2009 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 473 : 2023 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2001 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 2161 : 2006 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 2161 : 2022 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1363 : 2008 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 473 : 2022 : REV C | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2008 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 2161 : 2023 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2007 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2021 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2161 : 2023 : REV B | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1363 : 2023 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 2161 : 2021 : REV B | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1970 : 2023 | Standard Practice for Statistical Treatment of Thermoanalytical Data |
| ASTM E 2113 : 2018 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2022 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2014 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1363 : 2018 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 1363 : 2003 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2014 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2023 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1363 : 2013 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2005 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2015 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2021 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1970 : 2016 | Standard Practice for Statistical Treatment of Thermoanalytical Data |
| ASTM E 2113 : 2013 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 2161:2006 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 473 : 2022 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 473 : 2023 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1142 : 2011 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2021 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2007 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 1970 : 2006 | Standard Practice for Statistical Treatment of Thermoanalytical Data |
| ASTM E 2113 : 2004 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2023 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1970 : 2001 | Standard Practice for Statistical Treatment of Thermoanalytical Data |
| ASTM E 1970 : 2016 : R2021 | Standard Practice for Statistical Treatment of Thermoanalytical Data |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.