• There are no items in your cart

ASTM F 1004 : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures
Available format(s)

Hardcopy , PDF

Superseded date

06-05-2021

Language(s)

English

Published date

06-05-2019

This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.

1.1This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.

1.2Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.

1.3Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.

1.4No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.

1.5For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.

1.6The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.7The following pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 15
DocumentType
Standard
Pages
21
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 1487 : 2017 Standard Consumer Safety Performance Specification for Playground Equipment for Public Use
ASTM F 406 : 2019 Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards
ASTM F 3101 : 2015 Standard Specification for Unsupervised Public Use Outdoor Fitness Equipment
ASTM F 1487 : 2021 Standard Consumer Safety Performance Specification for Playground Equipment for Public Use

ASTM D 3359 : 2009 : EDT 2 Standard Test Methods for Measuring Adhesion by Tape Test
ASTM F 963 : 2007 Standard Consumer Safety Specification for Toy Safety
ASTM D 3359 : 1997 Standard Test Methods for Measuring Adhesion by Tape Test
ASTM D 3359 : 2009 Standard Test Methods for Measuring Adhesion by Tape Test
ASTM D 3359 : 2002 Standard Test Methods for Measuring Adhesion by Tape Test
ASTM D 3359 : 2009 : EDT 1 Standard Test Methods for Measuring Adhesion by Tape Test
ASTM D 3359 : 2007 Standard Test Methods for Measuring Adhesion by Tape Test
ASTM D 3359 : 2008 Standard Test Methods for Measuring Adhesion by Tape Test
ASTM D 3359 : 2017 Standard Test Methods for Rating Adhesion by Tape Test

View more information
US$108.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.