• There are no items in your cart

ASTM F 1987 : 2001 : R2011

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems (Withdrawn 2020)
Available format(s)

Hardcopy , PDF

Withdrawn date

01-08-2020

Language(s)

English

Published date

08-01-2011

CONTAINED IN VOL. 08.04, 2018 Defines requirements for multilayer pipe type 2 and compression fittings for hydronic heating systems, with a maximum pressure/temperature range of 1000 kpa (145 psi), at 82 degree C (180 degree F).

1.1 This specification covers requirements for multilayer pipe type 2 and compression fittings for hydronic heating systems, with a maximum pressure/temperature range of 1000 kPa (145 psi), at 82°C (180°F).

Note 1—Multilayer Pipe Type 2Construction-based pressure rated pipe comprising more than one layer in which at least 60 % of the wall thickness is polymeric material.

1.2 Multilayer pipe type 2 is produced using a butt-welded aluminum pipe as a core, with an extruded inside layer of crosslinked polyethylene (PEX). An adhesive layer is used to bond the inside layer to the wall of the aluminum pipe. An outer layer of polyethylene (PE) and an adhesive layer are extruded to the outer wall of the aluminum pipe.

1.3 Multilayer pipe type 2 is produced in Configurations 1 and 2, as shown in Fig. 1.

1.4 This specification includes compression fittings, which are referenced in Fig. 2.

1.5 Specifications for threaded or solder adapters for use with pipe and fittings meeting the requirements of this specification are given in Annex A1 and Annex A2.

1.6 The following safety hazards caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.

Committee
F 17
DocumentType
Standard
Pages
11
ProductNote
Reconfirmed 2011
PublisherName
American Society for Testing and Materials
Status
Withdrawn
Supersedes

ASTM F 412 : 2019 Standard Terminology Relating to Plastic Piping Systems

ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 3418 : 2015 : REDLINE Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 3222 : 2018 : REV A Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
ASTM D 1598 : 2002 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 3418 : 2012 : EDT 1 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 2122 : 1998 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 3418 : 1982 : R1988 : EDT 1 Standard Test Method for Transition Temperatures of Polymers By Thermal Analysis
ASTM D 1598 : 2015 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 3418 : 1999 Standard Test Method for Transition Temperatures of Polymers By Differential Scanning Calorimetry
ASTM D 1598 : 2015 : REV A Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 3222 : 1999 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
ASTM D 3222 : 2018 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
ASTM D 3350 : 2000 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3350 : 2008 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3350 : 2002 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 1505 : 2003 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM B 584 : 2014 : REDLINE Standard Specification for Copper Alloy Sand Castings for General Applications
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 3350 : 2014 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM F 477 : 2014 : REDLINE Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM D 3418 : 2012 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
SAE AS 568 : 2014 AEROSPACE SIZE STANDARD FOR O-RINGS
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 3418 : 2003 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 3418 : 2015 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 1598 : 1997 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 3350 : 2004 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3350 : 2002 : REV A Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3350 : 2012 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3350 : 2001 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 1898 : 1968 : R1989 Standard Practice for Sampling of Plastics (Withdrawn 1998)
ASTM D 3350 : 2012 : EDT 1 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2122 : 1998 : EDT 1 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 3222 : 2005 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
ASTM D 1505 : 1968 : R1979 Standard Test Method for Density Of Plastics By The Density-Gradient Technique
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 3350 : 2010 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3222 : 2005 : R2015 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
ISO 10508:2006 Plastics piping systems for hot and cold water installations Guidance for classification and design
ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 3418 : 2008 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 3222 : 2005 : R2010 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
ASTM D 1598 : 2002 : R2008 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 1505 : 2010 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 3350 : 2006 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 1505 : 2018 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 2122 : 1998 : R2004 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 3350 : 2010 : REV A Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 1505 : 1998 : EDT 1 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 1598 : 2002 : R2009 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2122 : 1998 : R2010 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 3350 : 2005 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2122 : 2015 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.