ASTM F 2881 : 2011

Name: ASTM F 2881 : 2011
Brand: ASTM
Price: 75.00 USD

Superseded

Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

03-01-2011

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 08.04, 2018 Defines requirements and test methods for dual wall polypropylene pipe and fittings. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm].

1.1 This specification covers requirements and test methods for dual wall polypropylene pipe and fittings. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm].

1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for nonpressure storm sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.

1.3 This specification covers pipe and fittings with an interior smooth wall and an annular corrugated profile outer wall (Fig. 1).

1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following precautionary statement caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee	F 17
DocumentType	Standard
Pages	8
ProductNote	Reconfirmed 2011
PublisherName	American Society for Testing and Materials
Status	Superseded

MIL-STD-129 Revision R:2014	Military Marking for Shipment and Storage
ASTM D 618 : 2013 : REDLINE	Standard Practice for Conditioning Plastics for Testing
ASTM A 666 : 2015 : REDLINE	Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
ASTM D 1238 : 2013 : REDLINE	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 792 : 2013 : REDLINE	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM F 477 : 2014 : REDLINE	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM D 4389/D4389M : 2016 : REDLINE	Standard Specification for Finished Glass Fabrics Woven From Rovings
ASTM D 3895 : 2014	Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
FED-STD-123 Revision H:2007	MARKING FOR SHIPMENT (CIVIL AGENCIES)
ASTM D 2444 : 1999	Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 790 : 2017 : REDLINE	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D 2122 : 2016 : REDLINE	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
AASHTO M 288 : 2015	SPECIFICATION FOR GEOSYNTHETIC SPECIFICATION FOR HIGHWAY APPLICATIONS
ASTM D 2990 : 2017 : REDLINE	Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D 6992 : 2016 : REDLINE	Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
ASTM D 638 : 2014 : REDLINE	Standard Test Method for Tensile Properties of Plastics