• There are no items in your cart

ASTM F 3010 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings
Available format(s)

Hardcopy , PDF

Superseded date

01-29-2024

Language(s)

English

Published date

08-27-2018

This practice covers the properties, application, and performance of a two-component resin based membrane-forming moisture mitigation system to high moisture concrete substrates prior to the installation of resilient flooring.

1.1This practice covers the properties, application, and performance of a two-component resin based membrane-forming moisture mitigation system to high moisture concrete substrates prior to the installation of resilient flooring.

1.2This practice includes recommendations for the preparation of the concrete surface to receive a two-component resin based membrane-forming moisture mitigation system.

1.3This practice does not supersede written instructions of the two-component resin based membrane-forming moisture mitigation system manufacturer, the resilient flooring manufacturer, underlayment manufacturer, the adhesive manufacturer, or other components of the finish flooring system, or combinations thereof. Users of this practice shall review manufacturer’s technical data sheets and installation instructions for compatibility of system components.

1.4The following membrane-forming or non membrane-forming moisture mitigation systems are not included in the scope of this practice:

1.4.1Moisture mitigation systems that chemically react with any constituent of the concrete to form a gel or crystalline substance within the concrete.

1.4.2Penetrating, water- or solvent-based compounds that do not form a continuous membrane on the concrete surface.

1.4.3Water-based membrane-forming moisture mitigation systems are not included in the scope of this document.

1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 06
DocumentType
Standard Practice
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 1869 : 2009 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 1869 : 1998 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 2420 : 2005 Standard Test Method for Determining Relative Humidity on the Surface of Concrete Floor Slabs Using Relative Humidity Probe Measurement and Insulated Hood
ASTM F 2170 : 2018 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM F 2170 : 2016 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM D 7234 : 2005 Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers
ASTM C 109/C109M : 2020 : REV B Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens)
ASTM F 2170 : 2016 : REV B Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM F 1869 : 2010 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 1869 : 2016 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 1869 : 2003 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 1869 : 2004 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM C 109/C109M : 2021 Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens)
ASTM D 7234 : 2019 Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers
ASTM F 2170 : 2016 : REV A Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM C 1583 : 2004 Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)
ASTM F 141 : 2012 : R2020 Standard Terminology Relating to Resilient Floor Coverings
ASTM C 109/C109M : 2020 : REV A Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
ASTM F 2420 : 2005 : R2011 Standard Test Method for Determining Relative Humidity on the Surface of Concrete Floor Slabs Using Relative Humidity Probe Measurement and Insulated Hood (Withdrawn 2014)
ASTM F 2170 : 2002 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using <bdit> in situ</bdit> Probes
ASTM D 7234 : 2012 Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers
ASTM F 1869 : 2016 : REV A Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 2170 : 2009 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using <bdit> in situ</bdit> Probes
ASTM F 2170 : 2011 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM F 1869 : 2011 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 2170 : 2017 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM C 109/C109M : 2016 : REV A Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
ASTM F 1869 : 2022 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 1869 : 2023 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
ASTM F 2170 : 2019 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM F 2170 : 2019 : REV A Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM D 7234 : 2021 Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers
ASTM F 141 : 2023 Standard Terminology Relating to Resilient Floor Coverings
ASTM D 7234 : 2022 Standard Test Method for Pull-Off Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.