• There are no items in your cart

AWWA C905 : 2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

POLYVINYL CHLORIDE (PVC) PRESSURE PIPE AND FABRICATED FITTINGS, 14 IN. THROUGH 48 IN. (350 MM THROUGH 1,200 MM), FOR WATER TRANSMISSION AND DISTRIBUTION
Superseded date

08-01-2016

Published date

01-01-2010

Foreword
 I Introduction
 II Special Issues
 III Use of This Standard
 IV Major Revisions
 V Comments
Standard
 1 General
 2 References
 3 Definitions
 4 Requirements
 5 Verification
 6 Delivery
Appendixes
 A - Bibliography
 B - Recurring (Cyclic) Surge - Figures and Design Example

Covers eight dimension ratio (DRs) and nominal pipe sizes ranging from 14 in. through 48 in. (350 mm through 1,200 mm).

DocumentType
Standard
PublisherName
American Water Works Association
Status
Superseded
SupersededBy
Supersedes

ASCE/EWRI 12-13, 13-13, 14-13 : 2013 STANDARD GUIDELINES FOR THE DESIGN, INSTALLATION, AND OPERATION AND MAINTENANCE OF URBAN SUBSURFACE DRAINAGE
ASME PCC 2 : 2015 REPAIR OF PRESSURE EQUIPMENT AND PIPING
ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 IRC® Code and Commentary, Volume 2
AWWA C605 : 2013 UNDERGROUND INSTALLATION OF POLYVINYL CHLORIDE (PVC) AND MOLECULARLY ORIENTED POLYVINYL CHLORIDE (PVCO) PRESSURE PIPE AND FITTINGS
AWWA M23 : 2 PVC PIPE - DESIGN AND INSTALLATION
AWWA M28 : 2014 REHABILITATION OF WATER MAINS

NSF 61 : 2016 DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS
AWWA M23 : 2 PVC PIPE - DESIGN AND INSTALLATION
PPI TR 3 : 2017 POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
ASTM F 477 : 2014 : REDLINE Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM D 2855 : 2015 : REDLINE Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets
AWWA C907 : 2017 INJECTION-MOLDED POLYVINYL CHLORIDE (PVC) PRESSURE FITTINGS, 4 IN. THROUGH 12 IN. (100 MM THROUGH 300 MM), FOR WATER, WASTEWATER, AND RECLAIMED WATER SERVICE
ASTM D 2241 : 2015 : REDLINE Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)
AWWA C605 : 2013 UNDERGROUND INSTALLATION OF POLYVINYL CHLORIDE (PVC) AND MOLECULARLY ORIENTED POLYVINYL CHLORIDE (PVCO) PRESSURE PIPE AND FITTINGS
ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2290 : 2016-12 TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE
AWWA C900 : 2016 POLYVINYL CHLORIDE (PVC) PRESSURE PIPE AND FABRICATED FITTINGS, 4 IN. THROUGH 60 IN. (100 MM THROUGH 1,500 MM)
ASTM D 1784 : 2011 : REDLINE Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.