Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search
Home
AWWA
AWWA C906:2015

AWWA C906:2015

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

POLYETHYLENE (PE) PRESSURE PIPE AND FITTINGS, 4 IN. THROUGH 65 IN. (100 MM THROUGH 1,650 MM), FOR WATERWORKS

Available format(s)

Hardcopy , PDF

Superseded date

12-13-2021

Language(s)

English

Published date

09-01-2015

Publisher

American Water Works Association

Foreword
 I Introduction
 II Special Issues
 III Use of This Standard
 IV Major Revisions
 V Comments
Standard
 1 General
 2 References
 3 Definitions
 4 Requirements
 5 Verification
 6 Marking and Shipping
Appendixes
 A - Internal Surge Pressure and Corresponding Sudden
     Water Flow Velocity Change
 B - Bibliography of Sources for Additional
     Information Regarding Permeation of Polyolefin Pipes

Specifies polyethylene (PE) pressure pipe and fittings made from materials conforming to standard PE materials designation codes PE 2606, PE 2706, PE 2708, PE 3608, PE 3708, PE 3710, PE 4608, PE 4708, and PE 4710.

DocumentType
Revision
ISBN
9781625760999
Pages
52
PublisherName
American Water Works Association
Status
Superseded
SupersededBy
Supersedes

AWWA M55 : 1 PE PIPE - DESIGN AND INSTALLATION
ASTM F 2880 : 2014 : REDLINE Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3/4</den></fraction > in. to 65 in.
ASME PCC 2 : 2015 REPAIR OF PRESSURE EQUIPMENT AND PIPING
CSA Z245.20 SERIES : 2014 PLANT-APPLIED EXTERNAL COATINGS FOR STEEL PIPE
FM 1613 : 2017 POLYETHYLENE (PE) PIPE AND FITTINGS FOR UNDERGROUND FIRE PROTECTION SERVICE
AWWA M28 : 2014 REHABILITATION OF WATER MAINS
NSF 14 : 2016 PLASTICS PIPING SYSTEM COMPONENTS AND RELATED MATERIALS

NSF 61 : 2016 DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS
ASTM D 3261 : 2016-11 SPECIFICATION FOR BUTT HEAT FUSION POLYETHYLENE (PE) PLASTIC FITTINGS FOR POLYETHYLENE (PE) PLASTIC PIPE AND TUBING
ASTM D 2839 : 2016 : REDLINE Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
ASTM D 1238 : 2013 : REDLINE Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
CAN/CSA-Z662-15 Oil and gas pipeline systems
PPI TR 3 : 2017 POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
AWWA C150/A21.50 : 2014 THICKNESS DESIGN OF DUCTILE-IRON PIPE
CSA B137.1 : 2009 GEN INS 1 11 POLYETHYLENE (PE) PIPE, TUBING, AND FITTINGS FOR COLD-WATER PRESSURE SERVICES
ASTM D 2683 : 2014 : REDLINE Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
ASTM D 1603 : 2014 : REDLINE Standard Test Method for Carbon Black Content in Olefin Plastics
ASTM D 2513 : 2017-01 SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS
ASTM F 714 : 2013 : REDLINE Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
AWWA C901 : 2017 POLYETHYLENE (PE) PRESSURE PIPE AND TUBING, 3/4 IN. (19 MM) THROUGH 3 IN. (76 MM), FOR WATER SERVICE
ASTM F 2619/F2619M : 2013 : REDLINE Standard Specification for High-Density Polyethylene (PE) Line Pipe
AWWA M55 : 1 PE PIPE - DESIGN AND INSTALLATION
ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM F 1055 : 2016-09 SPECIFICATION FOR ELECTROFUSION TYPE POLYETHYLENE FITTINGS FOR OUTSIDE DIAMETER CONTROLLED POLYETHYLENE AND CROSSLINKED POLYETHYLENE (PEX) PIPE AND TUBING
ASTM D 2290 : 2016-12 TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE
ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
CSA B137.4 : 2009 GEN INS 1 11 POLYETHYLENE (PE) PIPING SYSTEMS FOR GAS SERVICES

View more information
US$140.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English - DRM
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us