Name: BS 4500-1.2(1990) : AMD 7631
Brand: BSI

BS 4500-1.2(1990) : AMD 7631

Superseded

ISO LIMITS AND FITS - GENERAL, TOLERANCES AND DEVIATIONS - TABLES OF COMMONLY USED TOLERANCE GRADES AND LIMIT DEVIATIONS FOR HOLES AND SHAFTS

Superseded date

08-15-1993

Published date

11-23-2012

Publisher

British Standards Institution

Establishes values of the limit deviations for commonly used tolerance classes for holes and shafts calculated from the information given in ISO 286-1. Covers values for the upper deviations ES and es and the lower deviations EI and ei. Includes several tables and figures. BS AMD 7631 RENUMBERS THIS STANDARD TO BS EN 20286-2

Committee	GME/5
DevelopmentNote	Superseded and renumbered by BS EN 20286-2 (07/2004)
DocumentType	Standard
PublisherName	British Standards Institution
Status	Superseded
SupersededBy	BS EN 20286-2:1993
Supersedes	BS 4500-1:1969

Standards	Relationship
ISO 286-2:2010	Identical

BS 328-6:1992	Drills and reamers Countersinks, 90°, with parallel shanks and solid pilots
BS 3884-2:1990	Modular units for machine tools Specification for workholding pallets up to 800 mm nominal size
BS 1919-1:1993	Hacksaw blades Specification for hand and machine hacksaw blades
BS 341-1:1991	Transportable gas container valves Specification for industrial valves for working pressures up to and including 300 bar
BS 7724:1994	Specification for split pins (metric series)
BS AU 249:1993	Specification for clutch housings for reciprocating internal combustion engines. Nominal dimensions and tolerances
BS 4377:1991	Specification for tapping of holes to receive wire thread inserts (ISO metric threads)
BS 328-1:1993	Drills and reamers Specification for twist drills
BS 949-3:1993	Screwing taps. Specification for pipe thread taps
BS 4480-1:1992	Plain bearings: metric series Sintered bushes. Dimensions and tolerances
BS 7296-1:1990	Cavities for hydraulic fluid power cartridge valves Specification for two-port slip-in valves
BS 3884-3:1990	Modular units for machine tools Specification for workholding pallets over 800 mm nominal size
BS QC 030000:1993	Harmonized system of quality assessment for electronic components. Rectangular connectors for frequencies below 3 MHz. Generic specification. General requirements and guide for the preparation of detail specifications for connectors with assessed quality
BS 1574:1994	Specification for split pins (inch series)
BS 5594:1993	Specification for leaf chains, clevises and sheaves
BS 328-7:1992	Drills and reamers Counterbores with parallel shanks and solid pilots
BS 7637:1993	Specification for linear motion, recirculating ball, sleeve type rolling bearings (metric series)
BS 7586:1992	Specification for combination wrenches
BS 1759:1969	Specification for knurling wheels
BS EN 20898-2:1994	Mechanical properties of fasteners Nuts with specified proof load values. Coarse thread
EN 20898-2 : 1993	MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
BS 328-8:1992	Drills and reamers Spot drills
BS 5341-6.1:1992	Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabulary, inspection methods and generic specifications Vocabulary

ISO 8015:2011	Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
ISO 5166:1982	System of cone fits for cones from C = 1 : 3 to 1 : 500, lengths from 6 to 630 mm and diameters up to 500 mm
ISO 2692:2014	Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
ISO 1101:2017	Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 406:1987	Technical drawings Tolerancing of linear and angular dimensions
ISO 286-1:2010	Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
ISO/R 1938:1971	ISO system of limits and fits Part II : Inspection of plain workpieces
ISO 8062:1994	Castings System of dimensional tolerances and machining allowances