• There are no items in your cart

BS EN 1071-6:2007

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Advanced technical ceramics. Methods of test for ceramic coatings Determination of the abrasion resistance of coatings by a micro-abrasion wear test
Available format(s)

Hardcopy , PDF

Superseded date

08-31-2016

Language(s)

English

Published date

03-31-2010

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Significance and use
5 Principle
6 Apparatus and materials
   6.1 Test system
   6.2 Test balls
   6.3 Test slurry
   6.4 Measurement of crater dimensions
7 Preparation of test pieces
8 Test procedure
   8.1 Different types of test
   8.2 Test Type A: No perforation of coating
   8.3 Test Type B: Perforation of coating
9 Analysis of results
   9.1 Test Type A: no perforation of coating
   9.2 Test Type B: perforation of coating
10 Test reproducibility, repeatability and limits
   10.1 Reproducibility and repeatability
   10.2 Limits
11 Test report
Annex A (normative) - Measurement of coating thickness
Bibliography

Defines a method for measuring the abrasive wear rate of ceramic coatings by means of a micro-scale abrasion wear test, based on the well known crater grinding technique used for film thickness determination.

This part of EN 1071 specifies a method for measuring the abrasive wear rate of ceramic coatings by means of a micro-scale abrasion wear test, based on the well known crater grinding technique used for film thickness determination (see EN 1071-2).

This method can provide data on both film and substrate wear rates, either by performing two separate tests or by careful analysis of data from a single test series.

The test method can be applied to samples with planar or non-planar surfaces but the analysis described in clause 9 applies only to flat samples. For non-planar samples, a more complicated analysis, possibly requiring the use of numerical methods, is required.

Committee
RPI/13
DevelopmentNote
Supersedes DD ENV 1071-6 and 05/30136197 DC. (12/2007)
DocumentType
Standard
Pages
24
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes
UnderRevision

Standards Relationship
NBN EN 1071-6 : 2008 Identical
EN 1071-6:2007 Identical
NS EN 1071-6 : 1ED 2007 Identical
SN EN 1071-6 : 2008 Identical
NF EN 1071-6 : 2007 Identical
NEN EN 1071-6 : 2007 Identical
I.S. EN 1071-6:2008 Identical
DIN EN 1071-6:2008-01 Identical

ISO 3290:2001 Rolling bearings Balls Dimensions and tolerances
ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
EN 1071-1 : 2003 ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 1: DETERMINATION OF COATING THICKNESS BY CONTACT PROBE FILOMETER
ASTM A 485 : 2017 : REDLINE Standard Specification for High Hardenability Antifriction Bearing Steel
EN 1071-2 : 2002 ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 2: DETERMINATION OF COATING THICKNESS BY THE CRATER GRINDING METHOD
ASTM G 105 : 2016 Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests

View more information
US$237.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.