• There are no items in your cart

BS EN 13600:2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Copper and copper alloys. Seamless copper tubes for electrical purposes
Available format(s)

Hardcopy , PDF

Superseded date

04-21-2021

Language(s)

English

Published date

07-31-2013

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Designations
5 Ordering information
6 Requirements
7 Sampling
8 Test methods
9 Declaration of conformity and inspection documentation
10 Marking, packaging, labelling
Annex A (informative) - Characteristics of coppers for
        electrical purposes
Bibliography

Describes the composition, property requirements, including electrical properties, and tolerances on dimensions and form for seamless drawn copper tubes for electrical purposes.

This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for seamless drawn copper tubes for electrical purposes, delivered in straight lengths or alternatively in level wound coils with the cross-sections and size ranges below: - for round tubes in straight lengths with outside diameters from 3 mm up to and including 450 mm and wall thicknesses from 0,3 mm; - for round tubes in level wound coils with outside diameters from 3 mm up to and including 30 mm and wall thicknesses from 0,3 mm; - for square and rectangular tubes with major outside dimension from 5 mm up to and including 150 mm and wall thicknesses from 0,5 mm up to and including 10 mm. The sampling procedures and test methods for verification of conformity to the requirements of this standard are also specified.

Committee
NFE/34
DevelopmentNote
Supersedes BS 1977(1976) and 99/710680 DC (10/2002) Supersedes 11/30240453 DC. (07/2013)
DocumentType
Standard
Pages
30
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NF EN 13600 : 2013 Identical
SN EN 13600 : 2013 Identical
UNE-EN 13600:2014 Identical
NS EN 13600 : 2013 Identical
I.S. EN 13600:2013 Identical
DIN EN 13600:2013-09 Identical
NEN EN 13600 : 2013 Identical
NBN EN 13600 : 2013 Identical
EN 13600:2013 Identical
UNI EN 13600 : 2013 Identical
ONORM EN 13600 : 2013 Identical

ISO 6507-1:2005 Metallic materials Vickers hardness test Part 1: Test method
EN 1655:1997 Copper and copper alloys - Declarations of conformity
EN ISO 6506-1:2014 Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014)
ISO 6506-1:2014 Metallic materials Brinell hardness test Part 1: Test method
ISO 197-1:1983 Copper and copper alloys Terms and definitions Part 1: Materials
EN 1412:2016 Copper and copper alloys - European numbering system
ISO 1190-1:1982 Copper and copper alloys Code of designation Part 1: Designation of materials
EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)
ISO 8491:1998 Metallic materials Tube (in full section) Bend test
EN 1057:2006+A1:2010 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
ISO 1811-2:1988 Copper and copper alloys Selection and preparation of samples for chemical analysis Part 2: Sampling of wrought products and castings
ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
EN ISO 2626:1995 Copper - Hydrogen embrittlement test (ISO 2626:1973)
EN 1976:2012 Copper and copper alloys - Cast unwrought copper products
EN 12449:2016 Copper and copper alloys - Seamless, round tubes for general purposes
EN 1173:2008 Copper and copper alloys - Material condition designation
ISO 7438:2016 Metallic materials Bend test
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 10204:2004 Metallic products - Types of inspection documents
ISO 80000-1:2009 Quantities and units — Part 1: General
ISO 9001:2015 Quality management systems — Requirements
EN ISO 8491:2004 Metallic materials - Tube (in full section) - Bend test (ISO 8491:1998)
ISO 2626:1973 Copper Hydrogen embrittlement test
EN 50149:2012 Railway applications - Fixed installations - Electric traction - Copper and copper alloy grooved contact wires
EN ISO 7438:2016 Metallic materials - Bend test (ISO 7438:2016)

View more information
US$237.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.