BS EN 4476:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
10-03-2019
English
05-31-2011
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Batch release and qualification testing
6 Designation
Annex A (normative) - Method for the determination of
ability to selectively remove the finish
Annex B (normative) - Method for the determination of
ability to restore the paint system after removal
Annex C (normative) - Composition of reference paint remover
Bibliography
Describes the requirements for a two component polyurethane, topcoat, with a medium degree of resistance to erosion by the effects of rain, available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications on areas where rain erosion at subsonic speeds may be a problem, e.g. leading edges and air intakes.
This European Standard specifies the requirements for a two component polyurethane, topcoat, with a medium degree of resistance to erosion by the effects of rain, available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications on areas where rain erosion at subsonic speeds may be a problem, e.g. leading edges and air intakes. The properties specified in this European Standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837 Procedure A and EN 23270 and painted with primer to EN 2435-001 and -002. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions, etc.) should be determined by supplementary tests to confirm that the requirements of this European Standard are met.
Committee |
ACE/65
|
DocumentType |
Standard
|
Pages |
20
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
EN 4476:2011 | Identical |
EN 23270:1991 | Paints and varnishes and their raw materials - Temperatures and humidities for conditioning and testing (ISO 3270:1984) |
EN 2334 : 1997 | AEROSPACE SERIES - CHROMIC-SULPHURIC ACID PICKLE OF ALUMINIUM AND ALUMINIUM ALLOYS |
EN 4160:2011 | Aerospace series - Paints and varnishes - Determination of the effect of thermal exposure |
EN 2435-002:2006 | Aerospace series - Paints and varnishes - Corrosion resistant chromated two component cold curing primer - Part 002: High corrosion resistance |
PREN 2379 : 200P1 | AEROSPACE SERIES - FLUIDS FOR ASSESSMENT OF NON-METALLIC MATERIALS |
EN 2434-004:2010 | Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Part 004: High flexibility |
EN ISO 2431:2011 | Paints and varnishes - Determination of flow time by use of flow cups (ISO 2431:2011) |
ISO 3675:1998 | Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method |
ISO 2884-1:1999 | Paints and varnishes — Determination of viscosity using rotary viscometers — Part 1: Cone-and-plate viscometer operated at a high rate of shear |
ISO 1520:2006 | Paints and varnishes Cupping test |
EN 2435-001 : 2006 | AEROSPACE SERIES - PAINTS AND VARNISHES - CORROSION RESISTANT CHROMATED TWO COMPONENT COLD CURING PRIMER - PART 001: MINIMUM REQUIREMENTS |
EN ISO 2409:2013 | Paints and varnishes - Cross-cut test (ISO 2409:2013) |
ISO 11507:2007 | Paints and varnishes Exposure of coatings to artificial weathering Exposure to fluorescent UV lamps and water |
EN 3696 : 2001 | AEROSPACE SERIES - WASHERS IN HEAT RESISTING STEEL |
EN ISO 3675:1998 | Crude petroleum and liquid petroleum products - Laboratory determination of density - Hydrometer method (ISO 3675:1998) |
EN ISO 3251:2008 | Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO 3251:2008) |
EN ISO 9514:2005 | Paints and varnishes - Determination of the pot life of multicomponent coating systems - Preparation and conditioning of samples and guidelines for testing (ISO 9514:2005) |
ISO 3679:2015 | Determination of flash no-flash and flash point — Rapid equilibrium closed cup method |
EN ISO 2884-1:2006 | Paints and varnishes - Determination of viscosity using rotary viscometers - Part 1: Cone-and-plate viscometer operated at a high rate of shear (ISO 2884-1:1999) |
EN ISO 1513:2010 | Paints and varnishes - Examination and preparation of test samples (ISO 1513:2010) |
ISO 11890-1:2007 | Paints and varnishes — Determination of volatile organic compound (VOC) content — Part 1: Difference method |
EN ISO 3680:2004 | Determination of flash/no flash - Rapid equilibrium closed cup method (ISO 3680:2004) |
EN ISO 9117-1:2009 | Paints and varnishes - Drying tests - Part 1: Determination of through-dry state and through-dry time (ISO 9117-1:2009) |
ISO 9117-3:2010 | Paints and varnishes — Drying tests — Part 3: Surface-drying test using ballotini |
PREN 3837 : 200P1 | AEROSPACE SERIES - PAINTS AND VARNISHES - NATURE AND METHOD FOR SURFACE PREPARATION OF TEST PIECES IN ALUMINIUM ALLOYS |
ISO 3847:1977 | Liquid flow measurement in open channels by weirs and flumes — End-depth method for estimation of flow in rectangular channels with a free overfall |
ISO 1518:1992 | Paints and varnishes Scratch test |
EN ISO 1520:2006 | Paints and varnishes - Cupping test (ISO 1520:2006) |
EN ISO 11890-1:2007 | Paints and varnishes - Determination of volatile organic compound (VOC) content - Part 1: Difference method (ISO 11890-1:2007) |
TR 7000-9 : 1 | AEROSPACE SERIES - NON-METALLIC MATERIALS - RULES FOR THE DRAFTING AND PRESENTATION OF MATERIAL STANDARDS - PART 9: PAINTS AND VARNISHES |
ISO 6272-1:2011 | Paints and varnishes — Rapid-deformation (impact resistance) tests — Part 1: Falling-weight test, large-area indenter |
ISO 1513:2010 | Paints and varnishes Examination and preparation of test samples |
ISO 3251:2008 | Paints, varnishes and plastics Determination of non-volatile-matter content |
ISO 3680:2004 | Determination of flash/no flash Rapid equilibrium closed cup method |
ISO 3270:1984 | Paints and varnishes and their raw materials — Temperatures and humidities for conditioning and testing |
EN ISO 3679:2015 | Determination of flash no-flash and flash point - Rapid equilibrium closed cup method (ISO 3679:2015) |
EN ISO 1518:2000 | Paints and varnishes - Scratch test (ISO 1518:1992) |
ISO 9117-1:2009 | Paints and varnishes — Drying tests — Part 1: Determination of through-dry state and through-dry time |
ISO 2409:2013 | Paints and varnishes Cross-cut test |
ISO 9514:2005 | Paints and varnishes Determination of the pot life of multicomponent coating systems Preparation and conditioning of samples and guidelines for testing |
EN ISO 6272-1:2011 | Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 1: Falling-weight test, large-area indenter (ISO 6272-1:2011) |
EN 3840:2007 | Aerospace series - Paints and varnishes - Technical specification |
ISO 2813:2014 | Paints and varnishes Determination of gloss value at 20, 60 and 85 |
EN ISO 2813:2014 | Paints and varnishes - Determination of gloss value at 20°, 60° and 85° (ISO 2813:2014) |
EN ISO 9117-3:2010 | Paints and varnishes - Drying tests - Part 3: Surface-drying test using ballotini (ISO 9117-3:2010) |
ISO 2431:2011 | Paints and varnishes Determination of flow time by use of flow cups |
EN ISO 11507:2007 | Paints and varnishes - Exposure of coatings to artificial weathering - Exposure to fluorescent UV lamps and water (ISO 11507:2007) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.