Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search
Home
BSI
BS EN 60099-4:2014

BS EN 60099-4:2014

Current

Current

The latest, up-to-date edition.

Surge arresters Metal-oxide surge arresters without gaps for a.c. systems

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

09-30-2014

Publisher

British Standards Institution

INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Identification and classification
5 Standard ratings and service conditions
6 Requirements
7 General testing procedure
8 Type tests (design tests)
9 Routine tests and acceptance tests
10 Test requirements on polymer-housed surge arresters
11 Test requirements on gas-insulated metal enclosed
   arresters (GIS-arresters)
12 Separable and dead-front arresters
13 Liquid-immersed arresters
Annex A (normative) - Abnormal service conditions
Annex B (normative) - Test to verify thermal equivalency
        between complete arrester and arrester section
Annex C (normative) - Artificial pollution test with respect
        to the thermal stress on porcelain housed multi-unit
        metal-oxide surge arresters
Annex D (informative) - Typical information given with
        enquiries and tenders
Annex E (informative) - Ageing test procedure - Arrhenius
        law - Problems with higher temperatures
Annex F (informative) - Guide for the determination of the
        voltage distribution along metal-oxide surge arresters
Annex G (normative) - Mechanical considerations
Annex H (normative) - Test procedure to determine the
        lightning impulse discharge capability
Annex I (normative) - Determination of the start temperature
        in tests including verification of thermal stability
Annex J (normative) - Determination of the average
        temperature of a multi-unit highvoltage arrester
Annex K (informative) - Example calculation of test
        parameters for the operating duty test (8.7)
        according to the requirements of 7.3
Annex L (informative) - Comparison of the old energy
        classification system based on line discharge classes
        and the new classification system based on thermal
        energy ratings for operating duty tests and repetitive
        charge transfer ratings for repetitive single event
        energies
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Pertains to non-linear metal-oxide resistor type surge arresters without spark gaps designed to limit voltage surges on a.c. power circuits with U[s] above 1 kV.

IEC 60099-4:2014 applies to non-linear metal-oxide resistor type surge arresters without spark gaps designed to limit voltage surges on a.c. power circuits with Us above 1 kV. This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. The numerous changes between the second and third editions are listed in the Foreward of the document. Keywords: testing of gapless metal-oxide surge arresters for a.c.power systems

Committee
PEL/37
DevelopmentNote
Supersedes 90/23346 DC and 92/23905 DC. (08/2003) Supersedes 01/208948 DC. (10/2006) Supersedes 07/30167946 DC. (10/2009) Supersedes 11/30242671 DC. (10/2014)
DocumentType
Standard
Pages
172
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
IEC 60099-4:2014 Identical
I.S. EN 60099-4:2014 Identical
DIN EN 60099-4 : 2015 Identical
NF EN 60099-4 : 2015 Identical
SN EN 60099-4 : 2014 Identical
UNE-EN 60099-4:2016 Identical
EN 60099-4:2014 Identical
NBN EN 60099-4 : 2014 Identical

BS 7912(2012) : 2012 POWER CABLES WITH XLPE INSULATION AND METAL SHEATH, AND THEIR ACCESSORIES, FOR RATED VOLTAGES FROM 66 KV (U[M] = 72.5 KV) TO 132 KV (U[M] = 145 KV)
12/30244367 DC : 0 BS 7912 - POWER CABLES WITH XLPE INSULATION AND METAL SHEATH, AND THEIR ACCESSORIES, FOR RATED VOLTAGES FROM 66 KV (U[M] = 72.5 KV) TO 132 KV (U[M] = 145 KV)
BS EN 60071-2:1997 Insulation co-ordination Application guide

IEC 60060-2:2010 High-voltage test techniques - Part 2: Measuring systems
ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
EN ISO 4287:1998/A1:2009 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - TERMS, DEFINITIONS AND SURFACE TEXTURE PARAMETERS
IEC 60270:2000+AMD1:2015 CSV High-voltage test techniques - Partial discharge measurements
ISO 4287:1997 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
IEC 62271-200:2011 High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
IEC 62271-202:2014 High-voltage switchgear and controlgear - Part 202: High-voltage/ low-voltage prefabricated substation
EN ISO 4892-1:2016 Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016)
EN 62271-1:2017 High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
EN ISO 4892-3:2016 Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2016)
IEC 62217:2012 Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria
IEC TS 60815-2:2008 Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 2: Ceramic and glass insulators for a.c. systems
EN 62271-203:2012 High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
EN 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
IEC 60068-2-11:1981 Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
EN 60270:2001/A1:2016 HIGH-VOLTAGE TEST TECHNIQUES - PARTIAL DISCHARGE MEASUREMENTS (IEC 60270:2000/A1:2015)
EN 60507:2014 Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems
EN 60060-2:2011 High-voltage test techniques - Part 2: Measuring systems
ISO 4892-3:2016 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
IEC 62271-203:2011 High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV
IEC 60099-1:1991+AMD1:1999 CSV Surge arresters - Part 1: Non-linear resistor type gapped surge arresters for a.c. systems
ISO 3274:1996 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments
IEC 60721-3-2:1997 Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 2: Transportation
EN 60071-1:2006/A1:2010 INSULATION CO-ORDINATION - PART 1: DEFINITIONS, PRINCIPLES AND RULES
IEC 60099-5:2013 Surge arresters - Part 5: Selection and application recommendations
IEC 62271-1:2017 High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
CISPR TR 18-2:2017 Radio interference characteristics of overhead power lines and high-voltage equipment - Part 2: Methods of measurement and procedure for determining limits
IEC 60071-2:1996 Insulation co-ordination - Part 2: Application guide
ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
EN 60071-2:1997 Insulation co-ordination - Part 2: Application guide
EN 60068-2-11:1999 Environmental testing - Part 2: Tests - Test Ka: Salt mist
IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
IEC 60507:2013 Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems
IEC 60071-1:2006+AMD1:2010 CSV Insulation co-ordination - Part 1: Definitions, principles and rules
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC TS 60815-1:2008 Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles
EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 62217:2013 Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria
EN 62271-200:2012/AC:2015 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 200: AC METAL-ENCLOSED SWITCHGEAR AND CONTROLGEAR FOR RATED VOLTAGES ABOVE 1 KV AND UP TO AND INCLUDING 52 KV (IEC 62271-200:2011)
IEC TS 60815-3:2008 Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 3: Polymer insulators for a.c. systems

View more information
US$426.44
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us