IEC 60297-5-102:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-102: Subracks and associated plug-in units - Electromagnetic shielding provision
|
IEC 61076-4-113:2002
|
Connectors for electronic equipment - Printed board connectors - Part 4-113: Detail specification for two-part connectors having 5 rows with a grid of 2,54 mm for printed boards and backplanes in bus applications
|
IEC 60297-5-107:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear-mounted plug-in units
|
IEC 60297-5-105:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-105: Subracks and associated plug-in units - Alignment and/or earth pin
|
EN 60297-5-101:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-101: Subracks and associated plug-in units - Injector/extractor handle
|
IEC 60297-1:1986
|
Dimensions of mechanical structures of the 482.6 mm (19 in) series. Part 1: Panels and racks
|
IEC 60297-5-103:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-103: Subracks and associated plug-in units - Electrostatic discharge protection
|
HD 493.1 : 200S1
|
DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482.6 MM (19 IN) SERIES - PANELS AND RACKS
|
IEC 60297-5-101:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-101: Subracks and associated plug-in units - Injector/extractor handle
|
IEC 61587-1:2016
|
Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
|
IEC 60297-4:1995+AMD1:1999 CSV
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 4: Subracks and associated plug-in units - Additional dimensions
|
EN 60297-5-107:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear mounted plug-in units
|
EN 61587-1:2017
|
Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
|
IEC TS 61587-3:1999
|
Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets, racks and subracks
|
EN 60297-5-102:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-102: Subracks and associated plug-in units - Electromagnetic shielding provision
|
EN 60297-5-103:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-103: Subracks and associated plug-in units - Electrostatic discharge protection
|
EN 60297-5-105:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-105: Subracks and associated plug-in units - Alignment and/or earth pin
|
IEC 60297-5-104:2001
|
Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-104: Subracks and associated plug-in units - Keying
|
IEC 60603-2:1995
|
Connectors for frequencies below 3 MHz for use with printed boards - Part 2: Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features
|
EN 60297-4:1995/A1:1999
|
MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482.6 MM (19 IN) SERIES - SUBRACKS AND ASSOCIATED PLUG-IN UNITS - ADDITIONAL DIMENSIONS
|
EN 60603-2:1998/A1:2005
|
CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES
|
EN 61076-4-101:2001
|
Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917
|
IEC 61076-4-101:2001
|
Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917
|
HD 493.3 : 200S2
|
DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482.6 MM (19 IN) SERIES - SUBRACKS AND ASSOCIATED PLUG-IN UNITS
|
IEC 60917-1:1998+AMD1:2000 CSV
|
Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard
|