• There are no items in your cart

BS EN ISO 14692-1:2017

Current
Current

The latest, up-to-date edition.

Petroleum and natural gas industries. Glass-reinforced plastics (GRP) piping Vocabulary, symbols, applications and materials
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

10-06-2017

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviated terms
4 Pressure rating
5 Classification
6 Materials
7 Dimensions
Annex A (informative) - Principle
Annex B (informative) - Guidance on scope limitations
Annex C (normative) - Enquiry sheet
Annex D (normative) - Wall thickness definitions
Annex E (informative) - Selection of part factor f[3,est] in
        the bid process
Annex F (informative) - Worked example
Bibliography

Describes the applications, pressure rating methodology, the classification of the products according to application, type of joint and resin matrix and the limitations to both the materials of construction and the dimensions.

This document defines the applications, pressure rating methodology, the classification of the products according to application, type of joint and resin matrix and the limitations to both the materials of construction and the dimensions. It also lists the terms, definitions and symbols used and provides guidance in the use and interpretation of ISO14692‑2, ISO14692‑3 and ISO14692‑4.ISO14692(allparts) is applicable to GRP piping systems that 1) utilize joints that are capable of restraining axial thrust from internal pressure, temperature change and fluid hydrodynamic forces and 2) have a trapezoidal shape for its design envelope. It is primarily intended for offshore applications on both fixed and floating topsides facilities, but it can also be used for the specification, manufacture, testing and installation of GRP piping systems in other similar applications found onshore, e.g. produced-water, firewater systems and general industrial use.For floating installations, reference is made to the design, construction and certification standards for the hull or vessel, since these can allow alternative codes and standards for GRP piping associated with marine and/or ballast systems. However, it is recommended that ISO14692(allparts) be used for such applications to the maximum degree attainable.ISO14692(allparts) can also be used as the general basis for specification of pipe used for pump caissons, stilling tubes, I-tubes, seawater lift risers and other similar items.Typical oil and gas industry applications for the use of GRP piping and pipelines include those listed in Table 1.Table1Typical current and potential GRP piping oil and gas applicationsBallast waterHydrochloric acidBoiler feed waterInert gasBrineJet-A fuelCarbon Dioxide (CO2)Natural gasChlorine, gas, wetOilCondensate (water and gas)(Sour) Oil plus associated gasCooling water, sweet, brackish, seawaterPotable waterDemineralised waterProcess waterDiesel fuelProduced waterDrainsSeawaterEmulsions (water-oil-gas mixtures)Service waterFire water (ring main and wet or dry deluge)Sewer (grey and red)Formation waterSodium hydroxideFresh waterSodium hypochloriteFuelSour waterGas (methane, etc.)Unstabilized oilGlycolVentsHydrocarbon (with or without associated gas)WastewaterHydrogen chloride gas (HCl)Water disposalInjection waterNOTE Some applications, such as wet chlorine gas, hydrogen chloride gas, hydrochloric acid, sodium hydroxide and sodium hypochlorite, require a barrier liner and may require specific corrosion resistant resins. Consult the manufacturer for recommendations.

Committee
PSE/17/-/6
DevelopmentNote
Supersedes 00/716708 DC (01/2003)
DocumentType
Standard
Pages
80
PublisherName
British Standards Institution
Status
Current
Supersedes

ASTM D 3517 : 2014 : REDLINE Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe
ASTM D 3262 : 2016 : REDLINE Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe
ISO 10467:2004 Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
ANSI/AWWA C950:2013 FIBERGLASS PRESSURE PIPE
API SPEC 15HR : 2016 HIGH-PRESSURE FIBERGLASS LINE PIPE
ISO 14692-4:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 4: Fabrication, installation and operation
ISO 10639:2017 Plastics piping systems for pressure and non-pressure water supply Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
ISO 14692-2:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 2: Qualification and manufacture
EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
ASTM D 3754 : 2014 : REDLINE Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe
ASTM D 2992 : 2012 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ISO 14692-3:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 3: System design
EN 1796:2013 Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)

View more information
US$335.40
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.