• There are no items in your cart

BS EN ISO 1874-2:2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties
Available format(s)

Hardcopy , PDF

Superseded date

03-31-2017

Language(s)

English

Published date

12-31-2012

Foreword
1 Scope
2 Normative references
3 Preparation of test specimens
4 Conditioning of test specimens
5 Determination of properties
Annex A (normative) - Specimen preparation using
        laser sintering

Describes the methods of preparation of test specimens and the test methods to be used in determining the properties of polyamide moulding and extrusion materials.

Committee
PRI/82
DevelopmentNote
Supersedes 94/340137 DC. (09/2005) Supersedes 05/30091855 DC (02/2007) Supersedes 08/30190132 DC. (06/2011)
DocumentType
Standard
Pages
18
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
ISO 3167:2014 Plastics Multipurpose test specimens
ISO 1874-1:2010 Plastics Polyamide (PA) moulding and extrusion materials Part 1: Designation system and basis for specification
IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
ISO 294-3:2002 Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
ISO 27547-1:2010 Plastics — Preparation of test specimens of thermoplastic materials using mouldless technologies — Part 1: General principles, and laser sintering of test specimens
ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
ISO 1110:1995 Plastics Polyamides Accelerated conditioning of test specimens
ISO 8256:2004 Plastics — Determination of tensile-impact strength
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11357-3:2011 Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization
IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
ISO 294-4:2001 Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shrinkage
IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
ISO 472:2013 Plastics Vocabulary
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
ISO 307:2007 Plastics Polyamides Determination of viscosity number
ISO 1183-3:1999 Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 15512:2016 Plastics Determination of water content
ISO 62:2008 Plastics Determination of water absorption
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
ISO 3451-4:1998 Plastics — Determination of ash — Part 4: Polyamides

View more information
US$170.10
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.