• There are no items in your cart

BS EN ISO 3269:2001

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Fasteners. Acceptance inspection
Available format(s)

Hardcopy , PDF

Superseded date

10-15-2019

Language(s)

English

Published date

07-15-2001

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and conditions
4 General principles and requirements
5 Acceptance inspection procedure for fastener
   characteristics
Annex A (informative) Recommendations for acceptance-
   inspection procedures (for example, for dimensional
   characteristics)
Annex B (informative) Guidance and explanation
   concerning the principle of this international
   standard
Bibliography

Gives the procedure to be followed by the purchaser at his acceptance inspection so as to decide whether a lot of fasteners may be accepted or rejected, when another acceptance procedure has not been agreed.

Committee
FME/9
DevelopmentNote
Supersedes 97/713351 DC (06/2005) Reviewed and confirmed by BSI, January 2007. (12/2006)
DocumentType
Standard
Pages
30
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

BS 4933:2010 Specification for ISO metric black cup and countersunk head bolts and screws with hexagon nuts
BS 7419:2012 Specification for holding down bolts
12/30258706 DC : 0 BS 7419 - SPECIFICATION FOR HOLDING DOWN BOLTS

ISO 8839:1986 Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
ISO 10683:2014 Fasteners Non-electrolytically applied zinc flake coatings
EN 26157-3 : 1991 FASTENERS - SURFACE DISCONTINUITIES - PART 3: BOLTS, SCREWS AND STUDS FOR SPECIAL REQUIREMENTS (ISO 6157-3:1988)
ISO 4759-3:2016 Tolerances for fasteners Part 3: Washers for bolts, screws and nuts Product grades A, C and F
ISO 4042:1999 Fasteners Electroplated coatings
ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
ISO 6157-3:1988 Fasteners Surface discontinuities Part 3: Bolts, screws and studs for special requirements
EN ISO 4042:1999 FASTENERS - ELECTROPLATED COATINGS (ISO 4042:1999)
EN ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009)
EN ISO 3506-3:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:2009)
ISO 4759-1:2000 Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 6157-1:1988 Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements
EN 26157-1 : 1991 FASTENERS - SURFACE DISCONTINUITIES - PART 1: BOLTS, SCREWS AND STUDS FOR GENERAL REQUIREMENTS
ISO 2320:2015 Fasteners Prevailing torque steel nuts Functional properties
EN ISO 4759-3:2016 Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016)
ISO 7085:1999 Mechanical and performance requirements of case hardened and tempered metric thread rolling screws
ISO 8402:1994 Quality management and quality assurance — Vocabulary
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
ISO 1502:1996 ISO general-purpose metric screw threads Gauges and gauging
ISO 898-6:1994 Mechanical properties of fasteners Part 6: Nuts with specified proof load values Fine pitch thread
ISO 898-5:2012 Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar threaded fasteners with specified hardness classes Coarse thread and fine pitch thread
ISO 3506-3:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress
EN ISO 2702:2011 Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011)
ISO 3534-2:2006 Statistics Vocabulary and symbols Part 2: Applied statistics
EN ISO 898-5:2012 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (ISO 898-5:2012)
EN ISO 2320:2015 Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015)
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
ISO 6157-2:1995 Fasteners Surface discontinuities Part 2: Nuts
EN ISO 898-6 : 1995 MECHANICAL PROPERTIES OF FASTENERS - PART 6: NUTS WITH SPECIFIED PROOF LOAD VALUES - FINE PITCH THREAD
ISO 8992:2005 Fasteners — General requirements for bolts, screws, studs and nuts
ISO 2702:2011 Heat-treated steel tapping screws — Mechanical properties
ISO 1478:1999 Tapping screws thread
ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
EN ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009)

View more information
US$237.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.