|
IEC 60243-1:2013
|
Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
|
|
IEC 60112:2003+AMD1:2009 CSV
|
Method for the determination of the proof and the comparative tracking indices of solid insulating materials
|
|
ISO 4589-3:2017
|
Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test
|
|
ISO 75-1:2013
|
Plastics Determination of temperature of deflection under load Part 1: General test method
|
|
ISO 6603-2:2000
|
Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing
|
|
ISO 11667:1997
|
Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of resin, reinforced-fibre and mineral-filler content — Dissolution methods
|
|
ISO 527-4:1997
|
Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
|
|
IEC 60250:1969
|
Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
|
|
ISO 6603-1:2000
|
Plastics Determination of puncture impact behaviour of rigid plastics Part 1: Non-instrumented impact testing
|
|
ISO 295:2004
|
Plastics — Compression moulding of test specimens of thermosetting materials
|
|
ISO 1172:1996
|
Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of the textile-glass and mineral-filler content — Calcination methods
|
|
ISO 11359-2:1999
|
Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
|
|
ISO 75-2:2013
|
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
|
|
ISO 527-2:2012
|
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
|
|
ISO 3795:1989
|
Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials
|
|
ISO 1183:1987
|
Plastics Methods for determining the density and relative density of non-cellular plastics
|
|
IEC 60093:1980
|
Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
|
|
ISO 472:2013
|
Plastics Vocabulary
|
|
ISO 180:2000
|
Plastics Determination of Izod impact strength
|
|
ISO 2577:2007
|
Plastics Thermosetting moulding materials Determination of shrinkage
|
|
IEC 60695-11-10:2013
|
Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
|
|
ISO 179-1:2010
|
Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
|
|
ISO 14125:1998
|
Fibre-reinforced plastic composites Determination of flexural properties
|
|
ISO 62:2008
|
Plastics Determination of water absorption
|
|
ISO 4589-2:2017
|
Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
|
|
IEC 60243-2:2013
|
Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage
|
|
ISO 75-3:2004
|
Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
|
|
ISO 8604:1988
|
Plastics — Prepregs — Definitions of terms and symbols for designations
|
|
IEC 60695-2-10:2013
|
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
|
|
ISO 12114:1997
|
Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of cure characteristics
|
|
ISO 527-1:2012
|
Plastics Determination of tensile properties Part 1: General principles
|
|
EN 1842:1997
|
Plastics - Thermoset moulding compounds (SMC - BMC) - Determination of compression moulding shrinkage
|
Important note : All end users must be registered with an Account prior to user licenses being assigned.