• There are no items in your cart

BS ISO 4427-1 : 2007

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

View Superseded by
withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

PLASTICS PIPING SYSTEMS - POLYETHYLENE (PE) PIPES AND FITTINGS FOR WATER SUPPLY - PART 1: GENERAL
Available format(s)

Hardcopy , PDF

Withdrawn date

08-15-2019

Language(s)

English

Published date

01-01-2007

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviated terms
4 Material
5 Effect on water quality of pipes intended for conveyance
  of water for human consumption
Annex A (informative) - Pressure reduction coefficients
Annex B (informative) - Resistance to rapid crack
        propagation
Bibliography

Defines the general aspects of polyethylene (PE) piping systems (mains and service pipes) intended for the conveyance of water for human consumption, including raw water prior to treatment and water for general purposes.

Committee
PRI/88/2
DevelopmentNote
Supersedes 06/30144666 DC. (09/2007) 2007 Edition Re-Issued in April 2015 & incorporates AMD 1 2015. Supersedes 13/30264060 DC. (05/2015)
DocumentType
Standard
Pages
24
PublisherName
British Standards Institution
Status
Withdrawn
SupersededBy
Supersedes

Standards Relationship
ISO 4427-1:2007 Identical

EN 13244-1:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General
ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
ISO 4427-3:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings
ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
ISO 6964:1986 Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
CEN/TS 13244-7 : 2003 PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES, DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
ISO 3:1973 Preferred numbers Series of preferred numbers
ISO 4427-5:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 5: Fitness for purpose of the system
ISO 18553:2002 Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
ISO 13479:2009 Polyolefin pipes for the conveyance of fluids Determination of resistance to crack propagation Test method for slow crack growth on notched pipes
ISO 11414:2009 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
ISO 16871:2003 Plastics piping and ducting systems Plastics pipes and fittings Method for exposure to direct (natural) weathering
ISO 472:2013 Plastics Vocabulary
ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
ISO 15512:2016 Plastics Determination of water content
ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
ISO 13761:2017 Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C
ISO 6259-3:2015 Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes
EN 12201-1:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
EN 12099:1997 Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
CEN/TS 12201-7:2014 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
ISO 4427-2:2007 Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes

View more information
US$222.80
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.